RSP M0720-1 Скачать руководство пользователя страница 43

Страница: 43 / 64

M0720-1 ver 3.4

6.2 Replacement of tool attachment

Action

Note

Safety

Read the saf ety section (1.2).

Undock

tool

Place and undock tool
attachment, with tool
mounted, in a saf e and f ully
supported position f or
dismounting.

Dismount hoses

Dismount the water/air hoses
f rom the tool attachment.

NOTE!

Make sure that no dirt

enters the water/air hoses.

Disconnect

electric connections

Disconnect electric power
and signals.

NOTE!

Handle contacts with

care, as they are sensitive to
mechanical damage. Make
sure that no dirt enters the
contacts.

NOTE!

Be caref ul not to

damage the servo and weld
power pins.

Remove screws

Remove the screws holding
the tool attachment to the
tool.

NOTE!

The tool attachment

can be f itted to the
gripper/tool in two ways.

WARNING!

The tool

attachment is heavy and may
cause personal injury and
equipment damage if
dropped.

Содержание M0720-1

































































Результаты поиска

Содержание M0720-1

Отзывы:

Похожие инструкции для M0720-1

Бренды по названию

Популярные бренды

RSP M0720-1, Руководство по установке и обслуживанию

Результаты поиска

Содержание M0720-1

Отзывы:

Похожие инструкции для M0720-1

Бренды по названию

Популярные бренды