RS PRO RS510 Series Скачать руководство пользователя страница 7

Страница: 7 / 46

1.4 During Operation

Danger

➢

Do not connect or disconnect the motor during operation. Otherwise, It may cause

the inverter to trip or damage the unit.

Caution

➢

Do not touch heat radiating components such as heat sinks and brake resistors.

➢

The inverter can drive the motor from low speed to high speed. Verify the

allowable speed ranges of the motor and the associated machinery.

➢

Note the settings related to the braking unit.

➢

Risk of electric shock. The DC link capacitors remain charged for five minutes

after power has been removed. It is not permissible to open the equipment until 5
minutes after the power has been removed.

Caution

➢

The Inverter should be used in environments with temperature range from (14-

104

℉

) or (-10 to 40

℃

) and relative humidity of 95%.

Note: models with fan : -10~50

℃

, models without fan : -10~40

℃

Danger

➢

Make sure that the power is switched off before disassembling or checking any

components.

1.5 Inverter Disposal

Caution

Please dispose of this unit with care as an industrial waste and according to your
required local regulations.

➢

The capacitors of inverter main circuit and printed circuit board are considered as

hazardous waste and must not be burnt.

➢

The Plastic enclosure and parts of the inverter such as the cover board will

release harmful gases if burnt.

Danger

➢

To avoid electric shock, do not take the front cover off while power is on.

➢

The motor will restart automatically after stop when auto-restart function is

enabled. In this case, care must be taken while working around the drive and
associated equipment .

➢

The operation of the stop switch is different than that of the emergency stop

switch. The stop switch has to be activated to be effective. Emergency stop has
to be de-activated to become effective.

Содержание RS510 Series















































Результаты поиска

Содержание RS510 Series

Отзывы:

Бренды по названию

Популярные бренды

RS PRO RS510 Series, Руководство по эксплуатации

Результаты поиска

Содержание RS510 Series

Отзывы:

Бренды по названию

Популярные бренды