background image

8

 

TROUBLESHOOTING

Problem

Solutions

Fan will not start.

Fan sounds noisy.

Fan wobbles

CARE OF YOUR FAN

 

 

 

Here are some suggestions to help you maintain your fan.
1. Because of the fan's natural movement, some connections may become loose. Check the support 
    Connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not 
    Necessary to remove fan from ceiling.)
2. Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or 
    Lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration 
    or tarnishing. Do not use water when cleaning. This could damage the motor, or the wood, or possibly 
    cause an electrical shock.
3. You can apply a light coat of furniture polish to the wood blades for additional protection and enhanced 
    beauty. Cover small scratches with a light application of shoe polish.
4. There is no need to oil your fan.  The motor has permanently lubricated bearings.

WARNING: 

Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury.

-  Check circuit fuses or breakers.
-  Check line wire connections to the fan and switch wire connections in the switch housing.

-  Make sure all motor housing screws are snug.
-  Make sure the screws that attach the fan blade bracket to the motor hub is tight.
-  Make sure wire nut connections are not rubbing against each other or the interior
   wall of the switch housing.
-  Allow a 24-hour "breaking-in" period. Most noise associated with a new fan 
   disappear during this time.
-  If using an optional light kit, make sure the screws securing the glassware are tight.
   Check that light bulb is also secure.
-  Some fan motors are sensitive to signals from solid-state variable speed controls.
   If you have installed this type of control, choose and install another type of control.
-  Make sure the upper canopy is a short distance from the ceiling. It should not
   touch the ceiling.   

-  Check that all blade and blade arm screws are secure.
-  Most fan wobbling problems are caused when blade levels are unequal. Check this 
   level by selecting a point on the ceiling above the tip of one of the blades. Measure 
   this distance. Rotate the fan until the next blade is positioned for measurement. 
   Repeat for each blade. The distance deviation should be equal within 1/8".
-  Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.
-  If the blade wobble is still noticeable, interchanging two adjacent (side by side) 
   blades can redistribute the weight and possibly result in smoother operation.

Содержание 1021-PC













Отзывы: