manualshive.com logo in svg

Royce RC130, Руководство по эксплуатации, Страница: 9 / 14

Поделиться
Скачать
Royce RC130 Скачать руководство пользователя страница 9

Page 7 

STARTING, RUN-IN 

STARTING 

 

Electrical  installation  should  be  carried  out  by  a  qualified    
electrician. 
 
Before starting:- 

 

1. 

Check  that  the  oil  level  is  in  the  red  circle  of  the  sight 
glass. 

2. 

Ensure that belt guard will not rub on the flywheel. 

3. 

Check that all attached air hoses etc are double clamped 
and tight. 

 
RUN-IN 

 

1. 

Open air outlet so that pressure DOES NOT build up. 

2. 

Ensure  that  pulley  is  running  in  direction  of  the  arrow 
stamped into top of belt-guard. 

3. 

Run compressor for 30 minutes with nil load (pressure). 

4. 

Close  tank  valve  allowing  compressor  to  build  up       
pressure and cut off. 

5. 

Ensure  that  unloader  works.  You  will  hear  a  hiss  of  air 
from under the pressure switch, this hiss will stop after a 
few seconds. 

6. 

Check  that  all  nuts  and  bolts  are  tight,  belt  tension  is  
correct (10mm - 25mm deflection in centre), fittings are 
tight and there are no oil leaks. 

Содержание RC130















Отзывы:

Нет отзывов