background image

page

12

The motor or gear is broken, contact your Royal Easi-Move supplier.

Rollers slip on wheels:
Check distance of rollers to tires. You can move the rollers closer to the tire. In certain circumstances, one of
the trailer’s wheels may be moving on a surface with less traction than the other, in which case, you can move
the rollers closer to the tire.

IMPORTANT INFORMATION

Ensure the tire pressures are correct before use. Refer to manufacturers hand book.

Ensure the motors are disengaged before towing the trailer

It is impossible for a tandem-axle trailer to be turned and maneuvered in the same way as a single-
axle as the turning circle is greatly increased compared to a single-axle trailer. Also, the amount of
different maneuvers required to park your trailer is increased.
When the trailer is turning, the motors provide lower rotational speed on one side to help
enable direction change. This enables the trailer to maneuver with minimal tire ‘scrub’ or
being dragged along the ground, which can cause undue stresses on its tires, wheel hubs
and chassis

Stand clear of the motors when the Easi-Move is in use. Do not touch or go near the rollers when the
Easi-Move is in use or when the power is switched on.

Ensure children are away from the Travel Trailer when the Easi-Move is in use.

Ensure the caster wheel is securely in place before use.

Ensure the trailer is chocked and secure when the mover is disengaged.

Disclaimer

It is an express requirement of the use of EASI-MOVE, MOVER that such is fitted and/or installed exclusively by
the selling party. Failure to follow this express requirement will lead to invalidation of the warranty offered at
the time of purchase and could also lead to damage to your vehicle, and may cause injury and/or death.
Accordingly, in no event shall Unipart Leisure and Marine Limited be liable for any lost profits, lost savings, or
any other special, indirect, incidental or consequential damages however caused, whether for breach of

warranty, contract, tort negligence, strict liability or otherwise, arising in any way out of the failure by the
customer to adhere to the strict requirements with regard to the fitting and/or installing of the EASI-MOVE,

MOVER even if Unipart Leisure and Marine Limited has been advised of the possibility of, or could have
foreseen, such damages. And, save in respect for proved claims of death and/or personal injury caused by
Unipart Leisure and Marine Limited, the maximum liability of Unipart Leisure and Marine Limited to the

customer arising out of any failure to preform of EASI-MOVE, MOVER is limited to the price paid by the
customer for the EASI-MOVE, MOVER.

Содержание Easi-Move V4




















Отзывы: