background image

FIRE FRONTS & FRETS SUITABLE FOR THIS APPLIANCE.

The illustration shown is the recommended MACH II Front and Fret, if an alternate Front and Fret is used, it is
important to maintain the equivalent ventilation to that shown. Fronts and Frets are available under the following
part numbers: -

TYPE 

GC No 

CODE No 

TYPE 

GC No

CODE No

MACH 11 BLACK 

32 183 25

C022G 

JB BLACK 

32 183 38 

C019G

MACH 11 BRASS

32 183 48

C024G

63$5(6$1'6(59,&(

For spares and service, apply to your local Supplier, Installer or direct to the manufacturer, stating that the
appliance is a Super Hot Toaster quoting the GC Appliance Number and Serial Number from the data badge
located on the front controls panel.

Advantage should be taken of regular servicing and inspection for gas appliances to ensure their continued safe
operation.

6+2573$576/,67

Description

Crosslee No

GC No

Piezo Igniter

40245

397 686

Control Knob

40232

Control Valve

41833

Oxy-Pilot Burner Assembly

42313

170 415

Main Injector

41180

389 515

Coal Support

43010

Burner Inserts

42952

Front Simulated Coal

40481

Set of Coals

43011

Protective Side plates

41072

170 249

Maximum Heat Input (Gross)

6.95 kW 23700 Btu/h

Royal Cozyfires are manufactured by:

CROSSLEE plc

Aber Park Industrial Estate,

Aber Road, Flint, Flintshire. CH6 5EX

Spares Tel 01422 203963

Fax: 01422 204475

Service (GSA Ltd) 01703 516611

Customer Service 01422 200660

Fax 01422 206304

*Technical Help Line 0906 8633268

*Calls charged at 60p per minute

Содержание Super Hot Toater
















Отзывы: