Roundup HCT-2010 Скачать руководство пользователя страница 10

Страница: 10 / 24

P/N 1011139 Rev. G 11/15

ADJUSTING CONVEYOR BELT CHAIN

1. Turn the unit off, unplug the power

cord, and allow the unit to cool. Put
on Heat Resistant gloves and remove
the Top Cover and Heat Shield.

2. Make sure flap of the Silicone Belt is

accessible on the top side. Pull the
Silicone Belt Pins out of the zipper on
the Silicone Belts (Figure 6).

3. Unplug and remove the Butter Wheel

Assembly (Figure 2).

4. Face the front of the toaster. Push the

front of the conveyor IN and DOWN
so it locks into place. This will release
the belt tension and allow it to be
free.

5. Remove the Silicone Belt(s).
6. Remove one complete link from

Conveyor Belt Chain.

7. Replace the Silicone Belt(s). Secure with

the Belt Pin.

8. Reassemble the unit.

REPLACING CONVEYOR BELT CHAIN

1. Turn the unit off, unplug the power

cord, and allow the unit to cool.

2. Put on Heat Resistant gloves and

remove the Top Cover and Heat
Shield.

3. Make sure flap of the Silicone Belt is

accessible on the top side. Pull the
Silicone Belt Pins out of the zipper on
the Silicone Belts (Figure 6).

4. Unplug and remove the Butter Wheel

Assembly (Figure 2).

5. Face the front of the toaster. Push the

front of the conveyor IN and DOWN
so it locks into place. This will release
the belt tension and allow it to be
free.

6. Remove the Silicone Belt(s).
7. Disengage the Conveyor Belt Chain

from both sides (Figure 9b)

8. Remove the Conveyor Belt Chain from

the unit.

9. Install the new Conveyor Belt Chain. The

chain MUST be installed with the hooks
facing the direction of travel. See Figure
8a.

10. Reassemble the unit.

Figure 9a. Conveyor Chain (FRONT of toaster view)

Heel Side

Conveyor Chain

Crown Side

Conveyor Chain

Center Support

Cover

Large Arrows indicate direction of Belt Chain Travel

Conveyor Chains MUST

be installed with hooks

facing the direction of

travel (front to back)

BELT

STRAND

COMPLETED

INSTALLATION

DISCONNECT THE BELT CHAIN

USING NEEDLE-NOSE PLIERS

TO BEND LINK AS SHOWN.

CONNECT THE BELT CHAIN

USING NEEDLE-NOSE PLIERS

TO BEND LINK AND LOOP

UNDER THE NEXT LINK

Figure 9b. Disconnecting Conveyor

Chain

Содержание HCT-2010

























Результаты поиска

Содержание HCT-2010

Отзывы:

Похожие инструкции для HCT-2010

Бренды по названию

Популярные бренды

Roundup HCT-2010, Руководство пользователя

Результаты поиска

Содержание HCT-2010

Отзывы:

Похожие инструкции для HCT-2010

Бренды по названию

Популярные бренды