Rottler SG7MTS, Руководство по эксплуатации и обслуживанию

Страница: 102 / 111

Section 10 Safety Data Sheets SG7MTS Manual
www.rottlermfg.com
10-4
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
LBPH817776 - Multi-Way Oil HD
Page 3/6
Issue Date: 16-Apr-2018 Status: FINAL
inert material such as sand or vermiculite, and place in suitable container for disposal. If spilled on water remove with appropriate
methods (e.g. skimming, booms or absorbents). In case of soil contamination, remove contaminated soil for remediation or
disposal, in accordance with local regulations.
Recommended measures are based on the most likely spillage scenarios for this material; however local conditions and
regulations may influence or limit the choice of appropriate actions to be taken. See Section 13 for information on appropriate
disposal.
SECTION 7: Handling and storage
Precautions for safe handling:
Keep away from flames and hot surfaces. Wash thoroughly after handling. Use good personal
hygiene practices and wear appropriate personal protective equipment (see section 8). Spills will produce very slippery surfaces.
Do not enter confined spaces such as tanks or pits without following proper entry procedures such as ASTM D-4276 and 29CFR
1910.146. Do not wear contaminated clothing or shoes.
Conditions for safe storage: Keep container(s) tightly closed and properly labeled. Use and store this material in cool, dry,
well-ventilated area away from heat and all sources of ignition. Store only in approved containers. Keep away from any
incompatible material (see Section 10). Protect container(s) against physical damage.
" Empty " containers retain residue and may be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such
containers to heat, flame, sparks, or other sources of ignition. They may explode and cause injury or death. " Empty " drums should
be completely drained, properly bunged, and promptly shipped to the supplier or a drum reconditioner. All containers should be
disposed of in an environmentally safe manner and in accordance with governmental regulations. Before working on or in tanks
which contain or have contained this material, refer to OSHA regulations, ANSI Z49.1, and other references pertaining to cleaning,
repairing, welding, or other contemplated operations.
SECTION 8: Exposure controls/personal protection
Chemical Name ACGIH OSHA Mexico Phillips 66
Distillates, petroleum,
hydrotreated heavy
paraffinic
TWA: 5mg/m
3
STEL: 10 mg/m
3
as Oil Mist, if Generated
--- --- ---
Distillates, petroleum,
solvent-dewaxed heavy
paraffinic
TWA: 5mg/m
3
STEL: 10 mg/m
3
as Oil Mist, if Generated
--- --- ---
Residual oils, petroleum,
solvent-dewaxed
TWA: 5mg/m
3
STEL: 10 mg/m
3
as Oil Mist, if Generated
--- --- ---
Note: State, local or other agencies or advisory groups may have established more stringent limits. Consult an industrial
hygienist or similar professional, or your local agencies, for further information.
Note: This product, as supplied, does not contain any hazardous materials with occupational exposure limits established
by the region specific regulatory bodies
Engineering controls: If current ventilation practices are not adequate to maintain airborne concentrations below the established
exposure limits, additional engineering controls may be required.
Eye/Face Protection: The use of eye / face protection is not normally required; however, good industrial hygiene practice suggests
the use of eye protection that meets or exceeds ANSI Z.87.1 whenever working with chemicals.
Skin/Hand Protection: The use of skin protection is not normally required; however, good industrial hygiene practice suggests the
use of gloves or other appropriate skin protection whenever working with chemicals. Suggested protective materials: Nitrile rubber
Respiratory Protection:
Where there is potential for airborne exposure above the exposure limit a NIOSH certified air purifying
respirator equipped with R or P95 filters may be used.
A respiratory protection program that meets or is equivalent to OSHA 29 CFR 1910.134 and ANSI Z88.2 should be followed
whenever workplace conditions warrant a respirator's use. Air purifying respirators provide limited protection and cannot be used in
atmospheres that exceed the maximum use concentration (as directed by regulation or the manufacturer's instructions), in oxygen
Occupational exposure limits
The following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.
At this time, the other constituents have no known exposure limits.
Biological occupational exposure limits