background image

Pneumatic Positioner 

YT-1200 series 

                                                                            Product Manual 

 

Ver. 1.18 

43 

 

Maintenance 

7.1 

Pilot valve 

1) 

If  Supply  air  pressure  is  not  stable  or  Supply  air  is  not  clean,  the  positioner  may  not  function 

properly. Air quality and pressure should be checked regularly to see if the air is clean and pressure 

set is normal. 

2) 

If the pilot valve has to be removed from the unit, be cautious not to lose the O-ring attached to 

rear side of the pilot valve and the stabilizing spring between the pilot valve and the torque motor. 

3) 

On the back of the Auto Manual switch, there is a fixed orifice (0.3 pie) which could be clogged 

with dusts and other substances and lead to malfunction of the positioner. First of all, remove the 

pilot valve from the positioner and see if the holes on the screens are not clogged. If the screens 

are clean and the positioner is not functioning, remove the Auto-Manual switch and check the back 

of the switch and see if the orifice is clean. Clean the orifice with air and reassemble the switch 

and the pilot valve to the positioner and test once again. If the unit is still not working, use a 0.2 pie 

drill or pin and insert into the orifice hole at the back of the Auto-Manual switch. 

 
 

 

 

Fig. 8-1:    Pilot unit and Auto manual switch 

 
7.2 

Seals 

Once a year, it is recommend to check if there are any damaged parts of the positioner. If there are 

damaged rubber parts such as diaphragms, o-rings and, packings, replace with new ones. 

Содержание YT-1200 Series















































Отзывы: