manualshive.com logo in svg

Roth ROTILABO CR-DS 40, Руководство по эксплуатации

Поделиться
Скачать
Roth ROTILABO CR-DS 40 Скачать руководство пользователя страница 17

17

4

TECHNICAL DATA

4.5 Lubrication Data

Welch Directorr™ Premium vacuum oil is a triple-distilled hydrocarbon oil using severely hydro treated  
base stock. The oil is designed to resist breakdown at higher RPMs and operating temperatures of  
direct-drive vacuum pumps. The hydro treating virtually eliminates aromatics and sulfur to give good  
resistance to sludge and varnish formation over time in corrosive environments. Directorr™ Premium  
vacuum oil enables Welch direct-drive vacuum pumps to maintain the highest vacuum performance  
over time. The oil is light yellow.

CAS No.

64742-65-0

Vapour Pressure (at 25°C) 1×10

-6

 mbar (1×10

-6

 torr)

Viscosity (at 40°C)

65 cSt (305 SUS)

Specific Gravity

0.87

The technical data and operating characteristics of Rotary vane pumps are only guaranteed  
if original Welch Directorr™ Premium vacuum oil is used!

Содержание ROTILABO CR-DS 40









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды