Rotax 125 JUNIOR MAX evo Скачать руководство пользователя страница 51

Страница: 51 / 54

BRP-Rotax

INSTALLATION INSTRUCTION

RUN-IN PROCEDURE

WARNING

Non-compliance may result in serious injuries

or death!

Running-in has to be done with a “long” gear ratio

and a rich main jet (2 sizes bigger than the recom-

mended main jet based on altitude and

temperature.

ATTENTION

For the first 10 liters of fuel use a mixing ratio of

1:33 (= 3% or 0.3 liter oil per 10 liters of fuel).

NOTE

BRP-Rotax recommends to use XPS Kart - Tec
oil.

Step

Procedure

15 min. up to 10.000 rpm.
15 min. up to 12.000 rpm.
15 min. full load.

Reduce the main jet size step by step
(e.g. 172 - 170 - 168 ...).

NOTE

Make sure that the coolant temperature reaches
a minimum of 55 °C (130 °F).
At cold ambient temperature radiator needs to
get partly covered by tape.

Effectivity: 125 MAX evo, Junior MAX
evo, Mini MAX evo, Micro MAX evo

Page 5

Edition: March 01 2021

Содержание 125 JUNIOR MAX evo























































Результаты поиска

Содержание 125 JUNIOR MAX evo

Отзывы:

Похожие инструкции для 125 JUNIOR MAX evo

Бренды по названию

Популярные бренды

Rotax 125 JUNIOR MAX evo, Руководство по установке

Результаты поиска

Содержание 125 JUNIOR MAX evo

Отзывы:

Похожие инструкции для 125 JUNIOR MAX evo

Бренды по названию

Популярные бренды