Rotary SPO16 Скачать руководство пользователя страница 29

Страница: 29 / 32

32. Charger Cable & Overhead Switch Cable:

A) Plug the male end of the 10 foot charger cable

into the receptacle on the back of the DC

control

cabinet.

B) Route the charger and overhead switch cable

to the top of the power unit column extensions

by wire tying them to the overhead hose.

33. Overhead Switch:

Connect the overhead switch

cable to the overhead switch using the included

wire nuts.

34. Receptacle:

A) Mount the receptacle box to the extension directly

above the DC control cabinet with the included

#12-24NC x ¾” long pan head machine screws and

nuts, Figure 40. Be sure to mount #12 star washers

to one mounting screw as shown in Figure 40. This

is very important for grounding.

B) Remove the hole punch covering the hole in the

receptacle box than lines up with the hole in the

extension. Mount the included 1/2” cord grip thru

the hole in the extension and receptacle box.

C) Mount the included ground wire hook terminal

using the included green self-tapping ground

screw through the grounding hole in the

receptacle box.

D) Fasten the receptacle to the receptacle box cover

with the included fastener and the cover to the box

with the included fasteners. The ears on the top

and bottom of the receptacle may need to be

removed to allow it to fit inside the cover properly.

Fasten the tinned end inside the ground terminal of

the receptacle.

35. Electrical:

Have a certified electrician run

appropriate power supply to the 120 volt

receptacles mounted at the top of the lift.

LIFT ELECTRICAL INPUT: 110-120 Volt, 60 Hz, 3.15 Amps

Note: A separate circuit is not required for each

ShockWave DC powerunit.

CAUTION: Never operate the motor on line voltage.

Motor damage may occur.

36. Laser Spotter:

Mount the laser using the

instructions included with the laser spotting kit.

37. Plug-in Laser and Charger:

A) Plug the laser into the bottom receptacle and

wire tie it to the receptacle box, Figure 40.

B) Plug the charger cable into the top receptacle.

Check to make sure the charger lights are on.

If charger lights are not on, flip switch on back of

charger.

38. Close DC Control Cabinet:

Re-attach the front

plastic covers to the DC control cabinet using the

same button head cap screws, Figure 38.

Содержание SPO16

































Результаты поиска

Содержание SPO16

Отзывы:

Похожие инструкции для SPO16

Бренды по названию

Популярные бренды

Rotary SPO16, Руководство по установке

Результаты поиска

Содержание SPO16

Отзывы:

Похожие инструкции для SPO16

Бренды по названию

Популярные бренды