Rosslare AYC-E 5 Series Скачать руководство пользователя страница 44

Страница: 44 / 65

Controller Operation

AYC-Ex5/T65 Series Installation and Programming Manual

Normal/Secure

switch

Tamper event

N.C.

01 to 99 Aux.

relay release time

Normal/Secure

switch

Direct shunt

N.O.

01 to 99 Shunt

time

Door Monitor

Shunt

N.C.

01 to 99

Maximum shunt

time

Door Monitor

Forced door

N.C.

01 to 99 Forced

delay

Door Monitor

Door ajar

N.C.

01 to 99 Ajar

delay

LED control –

Green

Valid code

N.O.

01 to 99 Aux.

relay release time

LED control – Red Valid code

N.O.

01 to 99 Aux.

relay release time

The following subsections describe each Auxiliary mode.

4.9.9.1

Auxiliary Mode 0

Auxiliary input function:

Activates the auxiliary output

Auxiliary output activated by:

Valid user code, Auxiliary code, and

Auxiliary input
For example, in Auxiliary Mode 0, the controller can function as a

two-door controller. The auxiliary relay is to be attached to the lock

on the second door. The auxiliary setting defines the door open

time for the second door. The auxiliary input is to be attached to the

REX pushbutton for the second door. The Door Monitor input

feature for the second door is not enabled when using this mode.

4.9.9.2

Auxiliary Mode 1

Auxiliary input function:

Toggles Normal/Secure modes

Auxiliary output activated by:

Valid user code, Auxiliary code

For example, in Auxiliary Mode 1, the controller can function as a

two-door controller. The auxiliary relay is to be attached to the lock

Содержание AYC-E 5 Series


































































Результаты поиска

Содержание AYC-E 5 Series

Отзывы:

Бренды по названию

Популярные бренды

Rosslare AYC-E 5 Series, Инструкция по установке и программированию

Результаты поиска

Содержание AYC-E 5 Series

Отзывы:

Бренды по названию

Популярные бренды