Ross DRA-8604 Скачать руководство пользователя страница 21

Страница: 21 / 44

DRA-8604 User Manual (Iss. 02)

Installation • 2–7

Software Upgrades

The DRA-8604 can be upgraded in the field via the Network Controller Card in your openGear
frame. Note that DashBoard version 5.1.0 or higher is required for this procedure.

To upgrade the software on a card

Contact Ross Technical Support for the latest software version file.

Display the

Device View

of the card by double-clicking its status indicator in the

Basic

Tree View

From the

Device View

, click

Upload

to display the

Select file for upload

dialog.

Navigate to the

*.bin

upload file you wish to upload.

Click

Open

If you are upgrading a single card, click

Finish

to display the

Uploading to Selected

Devices

dialog. Proceed to step 8.

If you are upgrading multiple cards:

• Click

Next >

to display the

Select Destination

menu. This menu provides a list of

the compatible cards based on the card selected in step 2.

• Specify the card(s) to upload the file to by selecting the check box(es) for the cards

you wish to upload the file to.

• Verify that the card(s) you wish to upload the file to. The

Error/Warning

fields

indicate any errors, such as incompatible software or card type mismatch.

• Click

Finish

to display the

Uploading to Selected Devices

dialog.

Monitor the upgrade.

• The

Uploading to Selected Devices

dialog enables you to monitor the upgrade

process.

• Click

to complete the upgrade.

• The card(s) are temporarily taken offline during the re-boot process. The process is

complete once the status indicators for the

Card State

and

Connection

fields return

to their previous status.

Содержание DRA-8604













































Результаты поиска

Содержание DRA-8604

Отзывы:

Похожие инструкции для DRA-8604

Бренды по названию

Популярные бренды

Ross DRA-8604, Руководство пользователя

Результаты поиска

Содержание DRA-8604

Отзывы:

Похожие инструкции для DRA-8604

Бренды по названию

Популярные бренды