background image

 

Installation Guide Toyota Corolla

 

Rosen Entertainment Systems 

 

Copyright 2007 all rights reserved 

 Installation Guide 

 

DP-TY0824  Rev A 

 

 

Page 3 

 
 

5 - Remove the Factory Radio 

 
You will need to remove the Factory Radio and prepare the Rosen Multi-Media unit for installation.  The following steps 
will help guide you through this process. 
 

Note

: Be sure to inspect all brackets and clips to ensure they were not damaged during the removal process.  If any 

brackets or clips were damaged, replace them prior to installation of the Rosen unit. 

 

Step 1: Remove the Mounting 

Screws 

 

Step 2: Unplug the Electrical 

Connections 

Step 3: Remove the Factory 

Brackets and Clips 

Step 4: Reinstall the Factory 

Brackets and Clips on the 
Rosen Unit 

 

 

 

 

 

6 – Locate the GPS Antenna, Optional XM Antenna and iPod Interface 

 
You will need to mount the GPS and Optional XM Antennas on the exterior of the vehicle.  And mount the iPod Interface 
Connector in the vehicle. The following steps will help guide you through this process. 
 

Note

: Please route the GPS harness away from other power harnesses in the vehicle. This will help to ensure 

optimum performance of the GPS system. 
 

Note

: Please locate the iPod interface module in an area which can be serviced in the future.  The iPod cable is 

intended to be a serviceable item, which plugs into the iPod/XM Interface Module. 

 

 

Step 1: Mount the GPS and XM 

antenna in a location on 
the exterior of the Vehicle 

Step 2: Connect the Optional XM 

Tuner as shown below.  
Mount the tuner inside the 
vehicle 

Step 3: Mount the iPod/XM 

Interface module where it 
can be serviced in the 
future 

Step 4: Locate the iPod interface 

connector for use by the 
end-consumer 

 

 

 
 

It is the installer’s responsibility to ensure that the safety equipment in the vehicle is NOT 
adversely affected by installation of this system.  Ensure that the routing of the harnesses does 
NOT obstruct airbags, SRS or other safety devices. 

 
 
 
 
 

 

Use Caution.  See the OEM Service Manual for additional information on the removal process

 

Содержание DS-TY0820









Отзывы: