manualshive.com logo in svg

Rosemount 8732 Series, Справочное руководство

Поделиться
Скачать
Rosemount 8732 Series Скачать руководство пользователя страница 13

Reference Manual 

00809-0100-4663, Rev BA
January 2010

Rosemount 8732

www.rosemount.com

Section 2

Installation

Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-1
Transmitter Symbols   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-2
Pre-Installation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-2
Mechanical Considerations  . . . . . . . . . . . . . . . . . . . . . . . . page 2-2
Environmental Considerations  . . . . . . . . . . . . . . . . . . . . . page 2-3
Installation Procedures   . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-3
Sensor Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-11

This section covers the steps required to physically install the magnetic 
flowmeter. Instructions and procedures in this section may require special 
precautions to ensure the safety of the personnel performing the operations. 
Please refer to the following safety messages before performing any 
operation in this section.

SAFETY MESSAGES

This symbol is used throughout this manual to indicate that special attention 
to warning information is required.

Failure to follow these installation guidelines could result in death or serious injury:

Installation and servicing instructions are for use by qualified personnel only. Do not perform 
any servicing other than that contained in the operating instructions, unless qualified. Verify 
that the operating environment of the sensor and transmitter is consistent with the 
appropriate hazardous area approval.

Do not connect a Rosemount 8732 to a non-Rosemount sensor that is located in an 
explosive atmosphere.

Explosions could result in death or serious injury:

 

Installation of this transmitter in an explosive environment must be in accordance with the 
appropriate local, national, and international standards, codes, and practices. Please review 
the approvals section of the 8732 reference manual for any restrictions associated with a 
safe installation. 

Before connecting a handheld communicator in an explosive atmosphere, make sure the 
instruments in the loop are installed in accordance with intrinsically safe or non-incendive 
field wiring practices.

Electrical shock can result in death or serious injury

Avoid contact with the leads and terminals. High voltage that may be present on leads can 
cause electrical shock.

Содержание 8732 Series































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды