Rosemount 8732 Series Скачать руководство пользователя страница 15

Страница: 15 / 190

Reference Manual

00809-0100-4663, Rev BA
January 2010

2-3

Rosemount 8732

Figure 2-1. Rosemount 8732 Dimensional Drawing

ENVIRONMENTAL
CONSIDERATIONS

To ensure maximum transmitter life, avoid temperature extremes and
vibration. Typical problem areas include:

•

high-vibration lines with integrally mounted transmitters

•

warm-climate installations in direct sunlight

•

outdoor installations in cold climates.

Remote-mounted transmitters may be installed in the control room to protect
the electronics from a harsh environment and provides easy access for
configuration or service.

Rosemount 8732 transmitters require external power so there must be access
to a suitable power source.

INSTALLATION
PROCEDURES

Rosemount 8732 installation includes both detailed mechanical and electrical
installation procedures.

Mount the Transmitter

Remote-mounted transmitters may be mounted on a pipe up to two inches in
diameter or against a flat surface.

Pipe Mounting

To mount the transmitter on a pipe:

Attach the mounting bracket to the pipe using the mounting hardware.

Attach the 8732 to the mounting bracket using the mounting screws.

5.82

(148)

6.48 (165)

7.49 (190)

LOI Cover

4.97

(126)

8.81

(224)

3.00

(76)

3.07

(78)

4.97

(126)

/2”-14 NPT Electrical

Conduit Connections

(2 places with a 3rd

optional)

/2”-14 NPT Remote Junction

Box Conduit Connections (2

places)

Содержание 8732 Series































































































































































































Результаты поиска

Содержание 8732 Series

Отзывы:

Бренды по названию

Популярные бренды

Rosemount 8732 Series, Справочное руководство

Результаты поиска

Содержание 8732 Series

Отзывы:

Бренды по названию

Популярные бренды