Rosch Computer CA331-NR Скачать руководство пользователя страница 73

Страница: 73 / 162

BIOS Setup

Advanced ACPI Configuration

Configures additional ACPI functions.

Enable RSDP pointers

to 64-bit Fixed System

Description Tables.

BIOS SETUP UTILITY

← →

Select Screen

↑↓

Select Item

Change Option

General Help

F10 Save and Exit

ESC Exit

Advanced ACPI Configuration

ACPI Version Features

ACPI APIC Support

AMI OEMB Table

Headless Mode

Advanced

[ACPI v1.0]

[Enabled]

[Disabled]

ACPI Version Features

Selects the ACPI version. The options are ACPI v1.0 and ACPI v2.0.

ACPI APIC Support

The options are Enabled and Disabled. Includes ACPI APIC table pointer to
RSDT pointer list.

AMI OEMB Table

The options are Enabled and Disabled. Includes OEMB table pointer to R (X)

SDT pointer lists.

Headless Mode

Enables or disables the headless operation mode through ACPI. The options

are Enabled and Disabled.

Содержание CA331-NR



































































































































































Результаты поиска

Содержание CA331-NR

Отзывы:

Бренды по названию

Популярные бренды

Rosch Computer CA331-NR, Руководство пользователя

Результаты поиска

Содержание CA331-NR

Отзывы:

Бренды по названию

Популярные бренды