Ropex CIRUS UPT-6010 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 58

background image

Revision list

Version 2

UPT-6010

Seite 3

1

Revision list

2

General information

This CIRUS

®

temperature controller is manufactured according to DIN EN 61010-1. In the course of its

manufacture it passed through quality assurance, whereby it was subjected to extensive inspections and tests. As
a result of this, the product left our factory in perfect condition.
Please carefully read through the operating manual before using the CIRUS

®

temperature controller. Keep the

operating manual for later reference and make sure that information and functions important for the user are avail-
able.
The recommendations and warning notes contained in these operating instructions must be complied with, in
order to guarantee safe operation.
The device can be operated within the limits indicated in the "Technical Data" without impairing its operational
safety. Installation and maintenance may only be performed by technically trained, skilled persons who are familiar
with the associated risks and warranty provisions.

2.1

Copyright

All contents, in particular texts, photographs and graphics, are protected by copyright. All rights, including to rep-
lication, publication, editing and translation, are reserved.

2.2

Intended use

CIRUS

®

temperature controllers may only be used for heating and temperature control of heatsealing elements

which are expressly approved for them, and providing the regulations, notes and warnings contained in these
instructions are observed.
In case of non-observance or use contrary to the intended purpose, there is a risk that safety will be impaired or
that the heatsealing element, electrical wiring, transformer etc. will overheat. This is the personal responsibility of
the user.

Version

Change

1

• Creation of documentation

2

• Change to one column layout

• ROPEX logo changed

• Covering page with important features

• Additions in general information



section 2 "General information" on page 3

• Addition in Communication protocol: Status bit measurement interruption



section 8.6.10 "Measurement interruption (MU)" on page 28

• Extension of slot 1, subslots 4 with index 16 to 48: absolute calibration resistances



• Extension integrated webserver: presentation of calibration values



section 8.8.6 "Calibration page" on page 40

• Updating of how to order



section 13 "How to order" on page 55

«
1
2
3
4
5
...
»

Содержание CIRUS UPT-6010



























































Отзывы:

Нет отзывов

Похожие инструкции для CIRUS UPT-6010

Бренд: Gantner Страницы: 56

Evolution Series E9000

Бренд: GE Страницы: 44

PACSystems RX7i

Бренд: GE Страницы: 469

GuardSwitch 300 Series

Бренд: GE Страницы: 2

GuardSwitch 300 Series

Бренд: GE Страницы: 2

Masoneilan VariPak 28001

Бренд: GE Страницы: 24

Бренд: Bartec Страницы: 26

Бренд: Baninni Страницы: 26

Бренд: V2 Страницы: 48

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

EP Series Pro-Bloc

Бренд: Parker Страницы: 11

Бренд: Parker Страницы: 22

Бренд: Parker Страницы: 2

Clip Studio TABMATE

Бренд: CELSYS Страницы: 2

MIMIC HRNDWHEELS

Бренд: MRMC Страницы: 20

Бренд: Yolink Страницы: 23

IntelliCross TouchFree Kit

Бренд: Novax Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды