HARDWARE BOX CONTENT
Please locate and confirm that
you have the following parts:
TR
. toddler rail = 1
one bag of hardware with the following:
Allen wrench = 1
Required tools:
CAUTION:
Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver
Do not use a power screwdriver which
can cause screws to break or strip
(not
included).
Phillips screwdriver (not included)
FOR STATIONARY TYPE OF 4510 (newer version)
STEP 1s
STEP 2s
Tighten completely all the bolts remained untightened before.
PLEASE REFER TO “ASSEMBLY INSTRUCTIONS FOR YOUR 4510s STATIONARY / CONVERTIBLE CRIB”
(Two adults are required to complete this step)
M
STEP 5
4
#8
4
#11
(M)
STEP 4
STEP 3
4
#5
4
#10
S
STEP 1
2
#4 2
#10
2
#6
S
CP
STEP 1
4
#3
4
#10
(Two adults are required to complete this step, see Figures 1s & 2s for details)
TR
CP
4
#3 4
#10
1
S
CP
2
#4 2
#10 2
#6
4
#5 4
#10
4
#8 4
#11
STEP 2s
Unmount the mattress support ( ) (see
for details). Keep the resulted hardware for the next steps ( rounded head bolts
and
small washers
).
Adjust the mattress support
to its lowest position (see
for details).
Unmount one of the stationary side panels (see
for details). Keep the resulted hardware for the next steps ( Allen bolts
and
bigger washers
).
Unmount the stabilizer bar ( ) attached to the stationary side panel (see
for details). Keep the resulted hardware for the next steps ( Allen bolts
,
bigger washers
and
barrel nuts
).
Detach the stationary side ( ) from the two corner pieces (
) (see
for details). Keep the resulted hardware for the next steps ( Allen bolts
and
bigger washers
).
arefully s
stationary side
Attach the toddler rail (
) to the corner pieces (
) using
Allen bolts
,
bigger washers
and the Allen wrench supplied ( ).
Attach the stabilizer bar ( ) to the corner pieces (
)
Allen bolts
,
bigger washers
,
barrel nuts
Allen bolts
,
bigger washers
rounded head bolts
,
small washers
After completing
, your crib should look like the one depicted on the first page of this instruction booklet.
C
tore the
in a proper place, away from direct sunlight and moisture, taking care not to scratch the wood finish.
Do not tighten the bolts completely at this step,
you will be asked to do this later.
(follow the instructions attached to the stabilizer bar)
Push the barrel nuts into the holes drilled in the corner pieces then align the straight slot in the head of the barrel nut vertically, so the threads in the bolt will insert
in the barrel nut. You can adjust the position of the barrel nut with a flat head screwdriver (not supplied) or a coin. Push the Allen bolt through the stabilizer bar. Start the threads by
hand to assure you don't strip the threads, then use the suplied Allen wrench. Do not tighten the bolts completely at this step, you will be asked to do this later.
Attach the resulted panel to the crib using
and the Allen wrench supplied ( ). Do not tighten the bolts completely at this step, you will be asked
to do this later.
Attach the lowered mattress support ( ) to the stabilizer bars ( ) using
and a Phillips screwdriver (not supplied).
You have a total of
bolts, distributed as following:
Allen bolts (
+
) in the toddler rail (
),
Allen bolts (
+
+
) in the stabilizer bar ( ),
Allen
bolts (
+
) in the toddler rail panel,
rounded head bolts (
+
) in the stabilizer bars ( ),
rounded head bolts (
+
+
) in the mattress support (
)
using
and the Allen
wrench supplied ( ).
1
1
M
S
18
4
#3
#10
TR 2
#4
#10
#6
S 4
#5
#10
4
#8
#11
S 4
#7
#11
#9
MS .
REMINDER:
Содержание TR 4510
Страница 3: ...2 x 4 TR S CP CP 4 x 2 6 6 FIGURE 1d...
Страница 4: ...5 x 4 8 x 4 FIGURE 2d...
Страница 6: ...3 x 4 10 x 4 TR S CP CP 4 x 2 10 x 2 6 6 FIGURE 1s...
Страница 7: ...5 x 4 10 x 4 8 x 4 11 FIGURE 2s x 4...
