HARDWARE BOX CONTENT
1
2
Please locate and confirm that
you have the following parts:
TR
. toddler rail = 1
one bag of hardware with the following:
. Allen wrench =
. Allen bolt (1 15/16" or 50 mm) = 4
1
2
1
Required tools:
CAUTION:
Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver
Do not use a power screwdriver which
can cause screws to break or strip
(not
included).
Phillips screwdriver (not included)
FOR DROPSIDE TYPE OF 4510 (older version)
STEP 1d
STEP 2d
Tighten completely all the bolts remained untightened before.
PLEASE REFER TO “ASSEMBLY INSTRUCTIONS FOR YOUR 4510 DROPSIDE / CONVERTIBLE CRIB”
(Two adults are required to complete this step)
M
STEP 8
4
#8
(M)
STEP 7
STEP 6
4
#5
S
STEP 4
2
#4
2
#6
D
CP
STEP 2
CP
2
2
(Two adults are required to complete this step, see Figures 1d & 2d for details)
TR
CP
4
2
1
S
CP
STEP 2d
Unmount the mattress support ( ) (see
for details). Keep the resulted hardware for the next steps ( rounded head bolts
).
Adjust the mattress support
to its lowest position (see
for details).
Unmount the dropside panel (see
for details). Keep the resulted hardware for the next steps ( Allen bolts
).
Unmount the stabilizer bar ( ) attached to the dropside panel (see
for details). Keep the resulted hardware for the next steps ( Allen bolts
and
barrel nuts
).
Detach the dropside ( ) from the two corner pieces (
) (see
for details).
arefully s
Using a Phillips screwdriver (not supplied) you must completely remove all the factory mounted hardware involved in dropside moving, found on the corner pieces (
) of your crib.
You must remove:
-
metallic pins (from both corner pieces);
-
white plastic pins (from both corner pieces).
Attach the toddler rail (
) to the corner pieces (
) using
Allen bolts ( ) and the Allen wrench supplied ( ).
Attach the stabilizer bar ( ) to the corner pieces (
)
After completing
, your crib should look like the one depicted on the first page of this instruction booklet.
C
tore the dropside in a proper place, away from direct sunlight and moisture, taking care not to scratch the wood finish.
Remember: the resulted hardware is not a toy!
You must keep this hardware in a proper place, away from your children.
Do not tighten the bolts completely at this step, you will be asked to do
this later.
(follow the instructions attached to the stabilizer bar)
Push the barrel nuts into the holes drilled in the corner pieces then align the straight slot in the head of the barrel nut vertically, so the threads in the bolt will insert in the barrel nut.
You can adjust the position of the barrel nut with a flat head screwdriver (not supplied) or a coin. Push the Allen bolt through the stabilizer bar. Start the threads by hand to assure you
don't strip the threads, then use the suplied Allen wrench. Do not tighten the bolts completely at this step, you will be asked to do this later.
Attach the resulted panel to the crib using
Allen bolts (
) and the Allen wrench supplied ( ). Do not tighten the bolts completely at this step, you will be asked to do this later.
Attach the lowered mattress support ( ) to the stabilizer bars ( ) using
rounded head bolts (
) and a Phillips screwdriver (not supplied).
You have a total of
bolts, distributed as following:
Allen bolts ( ) in the toddler rail (
),
Allen bolts (
+
) in the stabilizer bar ( ),
Allen bolts (
) in the
toddler rail panel,
rounded head bolts (
) in the stabilizer bars ( ),
rounded head bolts (
+
) in the mattress support (
)
using
Allen bolts (
),
barrel nuts (
) and the Allen wrench supplied ( ).
2
#4 2
#6
1
4
#5
1
M
S
4
#8
18
4
2
TR 2
#4
#6
S 4
#5
4
#8
S 4
#7
#9
MS .
REMINDER:
Содержание TR 4510
Страница 3: ...2 x 4 TR S CP CP 4 x 2 6 6 FIGURE 1d...
Страница 4: ...5 x 4 8 x 4 FIGURE 2d...
Страница 6: ...3 x 4 10 x 4 TR S CP CP 4 x 2 10 x 2 6 6 FIGURE 1s...
Страница 7: ...5 x 4 10 x 4 8 x 4 11 FIGURE 2s x 4...
