ROMANOFF RE-1000-7 Скачать руководство пользователя страница 50

Страница: 50 / 53

9 Deforest Street, Amityville, New York, 11701 USA

www.romanoff.com

[email protected]

Troubleshooting and Correction

12. Troubleshooting and Correction

Warning!

In case of malfunctions, never open the turbine module!

Danger of electric shock!

Malfunction:

•

In case of a malfunction, check the indications on the front film.

•

Switch off the system at the unit switch and stop the production process.

•

Now, disconnect the system from mains.

•

Check the filters and fuses of the system and replace them if necessary.

•

Use the quick diagnosis or contact your sales partner if the problem persists.

Accident:

•

Firstly, remove the injured person from the danger area.

•

Switch off the system at the unit switch and stop the production process.

•

Now, disconnect the system from mains.

•

In case of an accident, follow the company-internal instructions; these always have
priority.

•

Observe your company-physician's instructions for handling the extracted substances.

12.1

Quick Diagnosis

Problem

Cause

Corrective Action

System does not start, no display
on the front film

Power cable not plugged in

Plug in the power cable

Fuses not inserted or defective

Check fuses and replace if necessary

No voltage on the socket being used

Check fuses

Power switch in Off position

Switch power switch ON

Incorrect mains voltage

Check mains voltage

Three-phase mains without neutral conductor

Check mains connection

System does not start, warning
signal audible, turbine error lights
up

Turbine failure / malfunction

Switch off the system and contact the manufacturer or national
representative

Filter saturation indicator lights up
(green+red)

Filter fully saturated

Using the filter status indicator (depending on the system
type), decide which filter needs to be changed and reorder
replacement filters

Error Temperature lights up

Temperature problem

Switch off the system and let it cool down. Check ambient
temperature and extraction hose (blocked, length/cross
section), restart the system, contact the manufacturer or
national representative if the error occurs again.

System does not start,
Run/Standby button flashes

System is in standby

Press the Run/Standby button

Interface incorrectly wired

Attention! Interface partly only optionally available!

Check interface

Pin 7 = +

Pin 8 = -

For bridge between pin 9 and pin 10, the remote control has
priority, switch system to Run via remote control

System is running, yellow warning
flashing, filter saturation indicator
lights up (green+yellow)

Filter partially saturated (depending on the system type,
the affected filter is also displayed in yellow)

Green area - Filter saturation OK

Yellow area - Re-order replacement filter

Red area - Filter completely saturated - replace

Speed cannot be changed on the
system

Remote control connected, external speed control (pin
14,15)

External speed control has priority over manually set speed on
unit

Содержание RE-1000-7






















































Результаты поиска

Содержание RE-1000-7

Отзывы:

Похожие инструкции для RE-1000-7

Бренды по названию

Популярные бренды

ROMANOFF RE-1000-7, Руководство пользователя

Результаты поиска

Содержание RE-1000-7

Отзывы:

Похожие инструкции для RE-1000-7

Бренды по названию

Популярные бренды