background image

6

Replacing the Head or Hoop Rubber

The performance of the head and/or hoop rubber will diminish with use over time. If the head is torn or becomes 

too fatigued, or impossible to tension correctly, then it should be replaced. If the hoop rubber is worn out, it too can 

be replaced. For replacing head or hoop rubber, please contact your dealer or a Roland service center.

Replacing the Head

1. 

Remove all tuning bolts from the PDX-8 or 

PDX-6.

NOTE

Do not apply excessive force to the sensor and cushion located 

under the head. Doing so can interfere with accurate detection, and 

may damage it.

2. 

Remove the old head.

3. 

Place the new head on the shell.

4. 

Attach the tuning bolts to the head and shell.

5. 

Next, adjust the tension of the head. Refer to 

“Adjusting the Head Tension”

 (p. 4).

*  Do not firmly tighten a single tuning bolt by itself. Doing so will 

make it impossible to tension the head evenly, and will cause 

malfunctions.

Specifications

PDX-8

PDX-6

Head Size

8 inches

6.5 inches

Triggers

2 (Head, Rim)

2 (Head, Rim)

Dimensions

266 (W) x 326 (D) x 62 (H) mm

10-1/2 (W) x 12-7/8 (D) x 2-1/2 (H) inches

227 (W) x 286 (D) x 63.5 (H) mm

8-15/16 (W) x 11-5/16 (D) x 2-1/2 (H) inches

Weight

1.3 kg

2 lbs 14 oz

1.1 kg

2 lbs 7 oz

Accessories

Owner’s Manual, Connection Cable, Drum Key

Options

Pad Mount (MDH series), Stand (MDS series)

*  In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.

Loosen

Tighten

Tuning bolts

Head

Rim rubber

Shell

Head sensor

Rim sensor

Drum key

Hoop rubber

Содержание V-Drums V-PAD PDX-8









Отзывы: