manualshive.com logo in svg

Roland OCTAPAD SPD-30, Руководство пользователя

Поделиться
Скачать
Roland OCTAPAD SPD-30 Скачать руководство пользователя страница 3

3

02: STEP FILTER

This is a filter whose cutoff frequency can be modulated in steps. You can specify the pattern by which the cutoff frequency will 

change.

Knob

Parameter

Value

Explanation

[Knob 3]

Cutoff Modify

-64–+63

Increases/decreases value for all steps

Cutoff Step 1-8

0–127

Cutoff frequency at each step
Increasing this value will raise the cutoff frequency.

Rate BPM Sync

OFF, ON

OFF: Rate specified as numerical value 

ON: Rate specified as note value

[Knob 1]

Rate

0–127, note

Rate at which 8-step sequence is to be repeated

Attack

0–127

Speed at which the cutoff frequency changes between steps

Filter Type

LPF, BPF, HPF, NOTCH

Filter type
Frequency range that will pass through each filter 

LPF: frequencies below the cutoff 

BPF: frequencies in the region of the cutoff 

HPF: frequencies above the cutoff 

NOTCH: frequencies other than the region of the cutoff

Slope

-12 dB, -24 dB, -36 dB

Filter slope (damping characteristics; amount of damping per octave)
-12 dB: gentle 

-24 dB: steep 

-36 dB: extremely steep

[Knob 2]

Resonance

0–127

Filter resonance level
Increasing this value will emphasize the region near the cutoff frequency.

Level

0–127

Output level

03: DRIVE

This is a low-pass filter equipped with overdrive. It cuts the upper range and adds distortion.

Knob

Parameter

Value

Explanation

[Knob 3]

Cutoff

0–127

Cutoff frequency of the filter
Increasing this value will raise the cutoff frequency.

[Knob 2]

Resonance

0–127

Filter resonance level
Increasing this value will emphasize the region near the cutoff frequency.

[Knob 1]

Drive

0–127

Amount of distortion

Содержание OCTAPAD SPD-30



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды