Roland KIWI-3P Скачать руководство пользователя страница 42

Страница: 42 / 60

Continuous Controllers

Second

Third

Notes

Bank Select MSB

$00 (00)

$00-$01

0=Bank Selection, 1=Pattern Selection, 2=Seq Selection

Used in conjunction with CC32 Bank Select LSB

Modulation Wheel Level

$01 (01)

$00-$7f (0-127)

Breath Controller

$02 (02)

$00-$7f (0-127)

Not Supported

Portamento Time

$05 (05)

$00-$7f (0-127)

NRPN MSB

$06 (06)

$00-$7f (0-127)

Not Supported

Overall Volume

$07 (07)

$00-$7f (0-127)

Sets VCA Level

DCO1 Coarse Tune

$08 (08)

$00-$18 (0-24)

x=0-24 (-12 → +12 notes)

DCO1 LFO

$09 (09)

$00-$7f (0-127)

DCO1 ENV

$0a (10)

$00-$7f (0-127)

DCO1 PW

$0b (11)

$00-$7f (0-127)

DCO1 PWM

$0c (12)

$00-$7f (0-127)

DCO1 DYN

$0d (13)

$00-$7f (0-127)

DCO2 Coarse Tune

$0e (14)

$00-$18 (0-24)

x=0-24 (-12 → +12 notes)

DCO2 Fine Tune

$0f (15)

$00-$64 (0-100)

0-100 = -50 → + 50 cents

DCO2 LFO

$10 (16)

$00-$7f (0-127)

DCO2 ENV

$11 (17)

$00-$7f (0-127)

DCO2 PW

$12 (18)

$00-$7f (0-127)

DCO2 PWM

$13 (19)

$00-$7f (0-127)

DCO2 DYN

$14 (20)

$00-$7f (0-127)

DCO Detune

$15 (21)

$00-$7f (0-127)

DCO Mix

$16 (22)

$00-$7f (0-127)

Mix ENV

$17 (23)

$00-$7f (0-127)

Mix DYN

$18 (24)

$00-$7f (0-127)

Chorus Rate

$19 (25)

$00-$7f (0-127)

VCA DYN

$1a (26)

$00-$7f (0-127)

VCF Low Pass Cutoff

$1b (27)

$00-$7f (0-127)

VCF Low Pass Resonance

$1c (28)

$00-$7f (0-127)

VCF LFO

$1d (29)

$00-$7f (0-127)

VCF ENV

$1e (30)

$00-$7f (0-127)

VCF KEY

$1f (31)

$00-$7f (0-127)

Bank Select LSB

$20 (32)

$00-$7f (0-127)

Selects Bank sets for Program Select

$00 (0) for Patches 1-128

$01 (1) for Patches 129-256
$02 (2) for Patches 257-384

$03 (3) for Patches 385-512

VCF HPF

$21 (33)

$00-$7f (0-127)

VCF DYN

$22 (34)

$00-$7f (0-127)

ENV 1 Attack

$23 (35)

$00-$7f (0-127)

ENV 1 Decay

$24 (36)

$00-$7f (0-127)

ENV 1 Sustain

$25 (37)

$00-$7f (0-127)

NRPN LSB

$26 (38)

$00-$7f (0-127)

Not Supported.

ENV 1 Release

$27 (39)

$00-$7f (0-127)

ENV 2 Attack

$28 (40)

$00-$7f (0-127)

ENV 2 Decay

$29 (41)

$00-$7f (0-127)

www.kiwitechnics.com

Kiwi-3P Matrix Upgrade User Manual v1.2

Содержание KIWI-3P





























































Результаты поиска

Содержание KIWI-3P

Отзывы:

Бренды по названию

Популярные бренды

Roland KIWI-3P, Руководство пользователя

Результаты поиска

Содержание KIWI-3P

Отзывы:

Бренды по названию

Популярные бренды