manualshive.com logo in svg

Roland JX-3P, Руководство пользователя

Поделиться
Скачать
Roland JX-3P Скачать руководство пользователя страница 31

31

3P Upgrade Special Functions

Setting Incoming Midi 
Channel

The incoming midi channel can be set to any channel from 0-16. 0=Omni 1-
16=channel number
This is set using the Global Parameter Edit B-1

Setting Outgoing Midi 
Channel

The outgoing midi channel can be set to any channel from 1-16.
This is set using the Global Parameter Edit B-2

Setting Sequencer 
Outgoing Midi Channel

The Sequencer outgoing midi channel can be set to any channel from 1-16.
This is set using the Global Parameter Edit B-3

Factory Restore 1

Programs 1-32 can be restored to factory original by the following actions
1) Press 'Tape Memory'. The Tape Memory Light will begin to flash
2) Press 'Bank D' button. The 'D' light will start to flash
3) Press 'Tone 16' button. The Tone 16 and Edit Write buttons will begin to fast 
flash.
4) Press Edit Write to start restore or Tape Memory to cancel
Only Programs 1-32 (Banks A & B) are overwritten and 

Memory Protect must be 

set to off

. To Cancel press Tape Memory before Write is pressed

The 3P will stop responding for a short period while the restore is being done.

Factory Restore 2

Programs 1-256 can be restored to factory settings by the following action
Press and hold Edit Write and Seq Write while powering the 3P on.

WARNING - There will be no confirmation and

all Tones, Sequences & Patterns will be cleared.

The 

Memory Protect must be set to off

. The 3P will stop responding while the 

restore is being done.

Program Update

The KiwiTechnics 3P Upgrade has built in ability to update the firmware should
updates become available. This section is entered by pressing the Tape button
while the 3P is powered on. The Update file is then 'played' into the 3P using
midiOX or similar. The update progress is displayed on the Tone Lights. Once
complete the Bank D button will light and the 3P should be repowered.

WARNING - 

If this procedure fails the 3P will be rendered

unusable and will require a replacement CPU from

KiwiTechnics. Use at your own risk.

The current releases are displayed on the Tone Selector lights for about 1 sec at 
power on. Tone 1 - 6 display the program release and 7 - 8 display the Bootloader
release. e.g. Tone 2, 3 & 7 would mean Prog v2.3 and BL v 1

www.kiwitechnics.com

3P Upgrade User Manual v400

Содержание JX-3P


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды