Roland DXY-1150A, Руководство пользователя

Страница: 36 / 45

34
Instruc- Compati- Format Parameter Range ([ ]: Default) Expanation
tion bility
SA SA; None
SC SC Xmin,Xmax,Ymin Xmin,Ymin: User : *1
,Ymax(,type(,left,bottom)); coordinate of P1
SC Xmin,Xfactor,Ymin Xmax,Ymax: User : *1
,Yfactor,type; coordinate of P1
SC; type: Scaling type : 0,1,2
left : 0—100 (%)
bottom : 0—100 (%)
Xfactor: User X : *1
coordinate of P1
Yfactor: User Y : *1
coordinate of P2
SG SG g; g: Group number : 0—8 [0]
SG;
SI SI w.h; w: Character width : *1 (cm) [0.285cm]
SI; h: Character height : *1 (cm) [0.375cm]
SL SL tanø; tanø: Character slant : *1 [0]
SL;
SM SM s; s: Character or symbol : CHR$ (33)—CHR$ (58)
SM; ,CHR$ (60)—CHR$ (126)
(If no parameter, symbol mode OFF)
SP SP n; n: Pen number : 0—8 [0]
SP;
SR SR w,h; w: Character width : *1 (%) [0.285cm]
SR; h: Character height : *1 (%) [0.375cm]
SS SS; none
TL TL lp(,lm); lp: Tick length in : *1 (%) [0.5%]
TL; positive direction
lm: Tick length in : *1 (%) [0.5%]
negative direction
UC UC (c,)É¢x1,É¢y1((,c), c: Pen cotrol value : -8388608—-9999,+9999—+8388607 • The number of allotted units of each font is as follows:
É¢x2,É¢y2...,É¢xn,É¢yn); xn: Number of Fixed character width font: 48(W) x 64(H)
UC; X-axis directional : -9998—+9998 Optimum character width font: 42(W) x 72(H)
moving units • Normal characters are plotted within the following range. It
yn: Number of : -9998—+9998 means that if you define a character so as to be accommodated in
Y-axis directional there, it becomes the same size as a normal character.
moving units Fixed character width font: 32(W) x 32(H)
Optimum character width font: 28(W) x 36(H)
UF UF d1(,d2,.....d20); d1—d20: : *2 The maximum number of parameter you can set is 20.
UF; Hatching spacing
partition ratio
VS VS v(,n); v: Pen speed : 1-42 cm/sec • The pen speed can be set in the unit of 1cm/sec.
VS; n: Pen number [Value by automatic pen sensing] • The parameter range of 1—8388607 is for no error.
: 1-8 [All eight pens] • If the pen speed is set over 42, it will be set at 42.
• If the pen number is set over 9, the instruction is ignored.
WD WD c1c2.....cn cn: Character
[label terminator]
WD [label terminator]
WG WG r,ø1,øc(,ød); r: Radius : *1 • You can input a polygon of up to 250 vertices into the polygon
ø1: Start angle : *3 buffer in the state of being initialized. If you, however, input a
øc: Center angle : *3 polygon of vertices more than the buffer capacity, an error occurs.
ød: Chord tolerance : *3 [5°]
XT XT; None • The default tick length of X-axis is 0.5% of (P2y-P1y) in the
positive and negative directions, respectively.
YT YT; None • The default tick length of Y-axis is 0.5% of (P2x-P1x) in the
positive and negative directions, respectively.