12
Discover5
Dec, 2002
HOW TO UPDATE THE SOFTWARE AND/OR TO LOAD THE TEST PROGRAM FROM
FLOPPY DISK
Insert the floppy disk containing either the Software program
Software Update Disk Discover5 (code:
7773536000)
or the Test program
Test Update Disk Discover5 (code: 7773537000)
into the FDD.
Turn the instrument on, keeping the buttons CHAIN, TOP and FADE OUT/IN pressed. The display visualizes:
Press the button TONE/ USER PROGRAM 2. The display visualizes:
Press the button TONE/ USER PROGRAM 1 to load the flash ROM. The display visualizes:
If the loading has been completed successfully, the writing COMPLETED appears on the display.
In case the loading fails, press the button TONE/ USER PROGRAM 2 to go back to the main menu.
Turn the power off and then turn it on again after a few seconds.
Test Mode
Turn the power on while keeping pressed the button ON/OFF in the D. BEAM CONTROLLER section.
The display visualizes the first page of the test main menu.
Test Main Menu
Pressing the button GROUP, the display visualizes the second page of the test main menu.
**** TEST MENU ( 1 / 2 ) ****
1. SWITCH & LED
2. ADC & ENCODER
3. LCD
4. KEYSCAN
5. TOUCH SCREEN
6. SMARTMEDIA
7. HARMONIZER
8. MIDI
Press GROUP to scroll menu
**** LOAD SYSTEM ****
Program
loading
…..
-----------------
Program
checking …..
-----------------
Flash
updating …..
-----------------
<< TURN INSTRUMENT ON AGAIN >>
**** LOAD SYSTEM ****
1 . CONTINUE
2 . EXIT
**** SYSTEM MENU ****
1 . DISPLAY VERSION
2 . LOAD SYSTEM
3 . SAVE SYSTEM
Turn the power off to exit test mode.
FIRST GROUP
1
SWITCH AND LED CHECK
Pressing the button TONE/ USER PROGRAM1 the display visualizes:
Every time you press a button, you hear a sound when you release it. On the upper left side of the display, the
name of the button pressed and the one of the next button to press are visualized. At the end of the test, the
display visualizes the writing COMPLETED. Press Exit to go back to the main menu.
Note:
If the Switch test has been already carried out, you can exit by pressing the buttons HARMONIZER and
EXIT at the same time.
2
ADC AND ENCODER CHECK
Pressing the button TONE/ USER PROGRAM 2, the display visualizes:
You can carry out all the test in sequence, as follows:
•
ENCODER check: turning the encoder leftwards, its value increases up to 255. Turning it rightwards, its value
decreases to 0.
•
BENDER, MODULATION, BALANCE, VOICE, HARMONY, EFFECTS, FOOTPEDAL checks: the display
visualizes the values of all these functions. These values go from 0 to +/-127.
•
XXX indicates the ON/OFF status of the FOOT SWITCH and SUSTAIN FOOT SWITCH pedals.
•
D-BEAM check: make sure that moving your hand vertically above the D-Beam, the value shown on the
display changes from 0 to 127. When your hand is not on the D-Beam the value must be 0.
Press EXIT to skip each test.
******ADC & ENCODER TEST******
BENDER …………….……..…
0 / +127 - 127
MODULATION ……...…….…
0 - 127
BALANCE ……...……………..
- 127 0 + 127
VOICE ……...………………....
0 + 127
HARMONY ……...…………....
0 + 127
EFFECTS …...……………........ 0 - 60 +127
DBEAM ……...……… ………
0 - 127
SUSTAIN FOOTSWITCH....…
XXX
FOOTSWITCH ……...……......
XXX
FOOTPEDAL ……...……...….
0 - 127
ENCODER ……...…………..… 0 - 255
Press EXIT to Skip.
***** SWITCH & LED TEST *****
XXXX XX XXX
**** TEST MENU ( 2 / 2 ) ****
1. FLASH
2. VIDEO OUTPUT
3. AUDIO TEST
4. DISK TEST
5.
6.
7.
8.
Press GROUP to scroll menu
