manualshive.com logo in svg

Rointe Dalis 200DHW4, Инструкция по эксплуатации

Поделиться
Скачать
Rointe Dalis 200DHW4 Скачать руководство пользователя страница 28

28

• 

Make sure that the keypad is not locked and that no other advanced procedure is in progress.

• 

Press and release the 

 button. The screen will show the first available code.

• 

Press either the 

 

or

 

 button until “rtc” appears on the screen. 

• 

You will now need to set the correct day of the week. Press and release the 

 button. The 

day is shown as 1 ... 7 (the number 1 is Monday). The screen will show “dd” followed by the two 
numbers that represent the day.

• 

Use the 

 or 

 buttons within 15 seconds to select the correct day.

• 

You will now need to set the correct hour. Press and release the 

 button. The screen will 

show “hh” followed by the two numbers that represent the time. The time is displayed in 24-hour 
format.

• 

Use the 

 or 

 buttons within 15 seconds to select the correct time.

• 

You will now need to set the correct minutes. Press and release the 

 button. The display will 

show “nn”, followed by the two numbers that represent the minutes.

• 

Use the 

 or 

 buttons within 15 seconds to select the correct minutes.

• 

Then press and release the 

  button to save your settings, or do not carry out any other 

operation for 15 seconds.

• 

To exit the procedure: press and release the 

 button or do not carry out any operation for 

60 seconds.

10.4.3. Programming the time slots for switching the product on / off

Before you can configure time slots for switch on/off, you must program the correct/current day and  
time as described in section 10.4.2. previously.

• 

Make sure that the keypad is not locked and that no other advanced procedure is in progress.

• 

Press and release the 

 button. “SP1” will appear on the screen.

To program the first time interval:

• 

Press and release either the 

 

or

 

 button within 15 seconds to select “HOn1” (the first 

time on) and / or “HOf1” (the first time off). Select “HOn2” and “HOf2” for the second on / off 
time.

• 

Press and release the 

 button.

• 

Press and release either the 

 

or

 

 button within 15 seconds.

• 

Press and release the 

 button or do not carry out any other operation for 15 seconds.

To program a time slot on a specific day of the week:

• 

After the previous procedure has been carried out, press either the 

 or 

 button and then 

release within 15 seconds to select “Hd1” (switch on time for day 1/Monday) and / or “Hd2. ..7“ 
(switching on time for days 2 to 7 / Tuesday to Sunday).

• 

Press and release the 

 button.

Содержание Dalis 200DHW4

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды