background image

18 

 

 

 

 

   SEASONAL CLEANING 

 

If the A/C will not be used for a long time, Please follow these 

steps to maintain it 

2

 

Pull out the water plug to drain.

 

Run the A/C in fan mode for 2H till the inside is dry. 

Turn off the A/C and unplug.

 

Wash the filter screen and reassemble it. Dismantle

 

the exhaust duct and keep it properly. Take the 

battery from the remote control.

 

Cover the A/C with a plastic bag and place it at a dry place.

 

 
 

If you haven't used it for a long time, please pay attention to the 
following points when you use it again

 

Confirm whether water plugs and filters are installed.

 

 

Check if the power cord is intact. If there is any damage, do not use it. 

Reinstall the remote battery.

 

Reinstall the other components according to the installation instructions.

 

 

COMMON FAILURES AND DIAGNOSIS 

 

 

Error-detecting code 

Multi-functional defection 

E1 

Error of the coil’s temperature sensor 

E2 

Error of indoor temperature sensor 

 

E4 

Anti-freezing protection: temperature of the coil is too low and the whole 
A/C is off. When temperature excesses 8  C  ,the protection is released 
and previous working state is recovered. 

 

 

 

 

 

 

INTELLIGENT ERROR DETECTION

 

1

 

2

 

4

 

3

 

5

 

6

 

7

 

1

 

2

 

3

 

4

 

Содержание R-892



















Отзывы: