Rohde & Schwarz VOR/ILS Analyzer EVS200 Скачать руководство пользователя страница 17

Страница: 17 / 68

VOR/ILS Analyzer EVS200

0796.1800.02

E-8

Chapter 2: Preparation for Operation

DC connection

Only connect the unit when the minus pole of the battery

is connected to vehicles ground (GROUND

input voltage: 9 to 15 VDC

Assembling the FO Cable Jack

Finish the supplied FO cable jack (0018.6700) as following with commercial PVC cables.

cable specification

PVC wiring performance according VDE 0281
wire cross section 1.0 mm

or more

colour RED for +VDC
colour BLUE for ground(

)

FO cable jack

order no.:

0018.6700

Pin connection of the FO cable jack

Assembling the FO cable jack

Finishing and connection to the Vehicle Board Supply

Strip the cable end ca. 8 mm and mount multicore.

Draw the cable through the enclosure and connect it according to the above pin connection of
the FO cable jack.

Fit the pull-relief and assemble the FO cable jack.

Connect the cable to the vehicle board supply.

When connecting the finished cable to the 12-VDC vehicle

board supply there is to perform a protection by a cable fuse

(T2.0 A) or a fuse on board!

Connect and lock the FO cable jack in the VDC input at the rear of the unit.

Содержание VOR/ILS Analyzer EVS200





































































Результаты поиска

Содержание VOR/ILS Analyzer EVS200

Отзывы:

Бренды по названию

Популярные бренды

Rohde & Schwarz VOR/ILS Analyzer EVS200, Руководство пользователя

Результаты поиска

Содержание VOR/ILS Analyzer EVS200

Отзывы:

Бренды по названию

Популярные бренды