manualshive.com logo in svg

Rohde & Schwarz FSMR, Руководство пользователя

Поделиться
Скачать
Rohde & Schwarz FSMR Скачать руководство пользователя страница 17

FSMR Measurement 

Examples 

1166.3311.12-01 1.15 

E-1 

 

DEMOD

RELATIVE

+- PEAK/2

2.   Relative Audio measurements – audio frequency response 

Press the 

DEMOD

 hotkey. 

  The analog demodulation menu is displayed. 

In the DEMOD menu press the 

RELATIVE

 softkey. 

  The RELATIVE menu is displayed.In the relative menu, only the 

detectors which have been switched on in the DETECTOR menu 
are available for relative measurements. 

In the RELATIVE menu press the 

RELATIVE DB % 

 softkey. 

  The actual measurement value of the detector will be saved as a 

reference value and the result display will change to a relative 
reading (indicated with 

K

0.00 %).  

 

Change the modulation frequency to 50 kHz 

The following settings are used on the generator: 

1.  Select the AM Modulation, 50 kHz modulation frequency. 

 

RELATIVE

RELATIVE

DB   %

 

Relative display – Change the Unit to dB 

Press the 

DEMOD

 hotkey. 

  The analog demodulation menu is displayed. 

In the DEMOD menu press the 

RELATIVE

 softkey. 

  The RELATIVE menu is displayed. 

In the RELATIVE menu press the 

+- PEAK/2 

 softkey. 

  The actual result display will change from a relative reading 

indicated in % to a dB reading. 

Fig.1-11 

Relative measurement in the demod mode 

 

Содержание FSMR






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды