Roger Technology AG/ALED12C, Инструкции и предупреждения для установщика, Страница: 26 / 40

EN
26
4.3
Installation procedure KB Series
If the arm is mounted on the barrier’s body, remove it.
Place the arm on a stable surface, making sure it is not scratched.
To insert the LEDs, proceed as follows (
Fig. 7
):
• Remove the cap from the end of the arm (detail
D
) loosen the
screw.
• Remove the two transparent side profiles.
• Making sure that the LEDs are facing outward ( detail E ), insert
the LED strip,the LED strip into the two transparent strips
pushing the rear part of the LED strip gently.
• Secure the rubber adhesive under the LED strip in line with the
bend to protect it from the sharp aluminium edge ( detail F ).
• Insert the two transparent side profiles.
• Close the cap of the boom with the supplied screws.
• Feed the cable from the other side of the flange through the
dedicated hole indicated in detail G .
To install the rod, follow the steps below:
• Pass the cable through the hole provided on barrier’s structure
(figure 8, detail H) .
• Secure the flange to barrier’s structure carefully observing
cable's path.
• Fix the rod to the flange
• Pull the free section of the cable while conveying it to the
opposite side
(figure 9, detail I)
• The free part of the cable is now found inside the body of
the barrier, behind the reduction gear. Take the cable to the
command unit passing to the right of the reduction gear and
rising towards the casing.
Carry out the connections to the command unit as shown in
Fig. 10.
Connect the brown (or red) wire to the +LUCI terminal and connect
the blue (or black) wire to the
COM
terminal.
To see how to configure the lights, please refer to the manual of the
command unit (setting of parameter
79
).
4.4
Installation procedure BIONIK4
Series
If the arm is mounted on the barrier’s body, remove it.
Place the arm on a stable surface, making sure it is not scratched.
To insert the LEDs, proceed as follows (Fig. 11):
• Undo the 4.2x19 mm self-tapping cylindrical socket head cap
screws from the boom mount.
• Remove the boom mount cover
detail D
.
• Undo the 4.2x13 mm cylindrical socket head cap screws and
remove the boom end cap
detail E
.
• Feed the LED light strip detail F into the PVC moulding until it
comes out at the other end.
• Fold the excess length of LED light strip, push it into the
aluminium moulding and fasten with the cable tie included
detail G .
• Route the cable of the LED light strip correctly
detail H
as shown
in figure 12.
• Secure the cable with the relative cable fasteners
detail I
.
• Feed the cable in the hole in the centre of the boom mount detail L .
• Push the LED light strip cable out of the opposite end of the gear
motor unit detail M , securing with the cable fastener included
(fig. 13
detail N
).
• Feed the cable into the control unit, ensuring that the cable will
not interfere with the movements of the automation system.
Connect the cable to the control unit as shown in fig. 14. Connect
the brown (or red) wire to the +LUCI terminal and connect the blue
(or black) wire to the
COM
terminal.
Refer to parameter 79 of the control unit for setting up the LED
light strip.
4.5
Installation procedure BIONIK1-
BIONIK4HP-BIONIK6 Series
If the arm is mounted on the barrier’s body, remove it.
Place the arm on a stable surface, making sure it is not scratched.
To insert the LEDs proceed as follows (figure
15
):
• Unscrew the 6 M8 screws and remove the boom support cover.
• Unscrew the screws and remove the cap of the boom detail
D
.
• Remove the two transparent side profiles.
• Ensuring that the LEDs are facing outwards (detail
E
), insert the
LED strip into the two transparent profiles by gently pushing the
rear part.
• Fix the adhesive rubber under the LED strip at the curve to
protect it from the sharp aluminium profile (detail
F
).
• Insert the transparent profiles in the boom.
• Pass the LED light strip cable through the centre hole of the
boom support detail G .
• Push the cable out of the opposite end of the gear motor unit
through the rubber cable guide to the centre of the spring linkage
lever (Fig.
16-17
).
• Introduce the cable into the rubber cable guide present in the
barrier support structure.
• Introduce the cable into the control unit, ensuring that the cable
will not interfere with the movements of the automation system.
Connect the cable to the control unit as shown in
fig. 18
. Connect
the brown (or red) wire to the +LUCI terminal and connect the blue
(or black) wire to the
COM
terminal.
Refer to parameter 79 of the control unit for setting up the LED
light strip.
4.6
Installation procedure BIONIK8
Series
If the arm is mounted on the barrier’s body, remove it.
Place the arm on a stable surface, making sure it is not scratched.
To insert the LEDs, proceed as follows (Fig. 19 ):
• Unscrew the 6 M8 screws and remove the boom support cover
(detail D ).
• Unscrew the 2 TCC 4,2x13 screws and remove the cap of the
boom detail E .
• Insert the LED light strip [ F ] inside the PVC profile, with the LEDs
upwards, until it comes out from the opposite end.
• Fold the excess length of LED light strip into the aluminium
moulding and fasten it with the cable tie included (detail G ).
• Pass the LED light strip cable through the centre hole of the
boom support (detail H ) Fig. 20.
• Push the cable out of the opposite end of the gear motor unit
through the rubber cable guide to the centre of the spring linkage
lever (detail I , Fig. 21).
• Introduce the cable into the rubber cable guide present in the
barrier support structure.
• Introduce the cable into the control unit, ensuring that the cable
will not interfere with the movements of the automation system.
Connect the cable to the control unit as shown in fig. 22. Connect
the brown (or red) wire to the +LUCI terminal and connect the blue
(or black) wire to the COM terminal.
Refer to parameter
79
of the control unit for setting up the LED
light strip.