Installation Manual
Alcar
®
H51
10
button;
a successful learning
will be confirmed by
an optical-acoustical signal
;
5
) To clear all the remote controls from the central unit memory
press simultaneously both
remote control buttons of a known remote control.
The clearing of all remote controls at
once
will be confirmed by
three optical-acoustical signals
;
6)
To leave the learn mode
switch the contact key to ON position. Also, leaving the learn
mode will automatically be made after 15s. in which there is no remote control button pressed.
Notes:
a) The remote controls record in the central unit memory is made cyclically from location 1 to location
4, respecting FIFO principle (First In First Out). So, if the memory is full, the oldest remote control will
be erased when learning a new one.
b) By simultaneously pressing bot buttons of a new remote control, while in learning mode, then the
system will learn that remote control. (It will not be executed the operation of clearing all the remote
controls).
c) If the same remote control is learnt twice, it will be confirmed second time too, but it will not fill a
second memory location.
1)
In the case a remote control was stolen or lost
a
clearing of all the remote
controls at once
operation will be effected. Then, the remained remote controls and the new ones
will be learnt
2)
In the case all remote control were stolen or lost
a
new remote control learning
operation will be effected. Then a
clearing of all the remote controls at once
operation will be
effected followed by a learning operation for the new remote controls.
5.2 S
YSTEM
PARAMETERS
PROGRAMMING
Table I: SYSTEM PARAMETERS (
default values
in bold
)
N o .
P aram eter d escrip tio n
Op tical-aco ustical sig n al
1 sign al
2 sign als
0
S iren type
P o sitive trig gered
Negative triggered
1
C entral door lock timing
0,8s (electrical)
4s (pneumatically)
2
Reverse car moving warning
o ptical-acou stical
Optical only
3
Warning for door open
o ptical-acou stical
Optical only
4
P assive arming
enabled
d isab led
5
Temporarily disabling the passive arm ing
enabled
disabled
6
Unlock the doors when disarm ing
enabled
disabled
7
Unlock the doors when turning OF F the
engine
enabled
d isab led
8
Lock the doors when turning ON the
engine
enabled
d isab led
15
the remote controls is about 30m. The remote control is provided to 2 buttons, which will be referred
as 1 and 2.
The remote control is also provided with a LED that turns on when pressing any of the buttons. If
one note decreasing of the light intensity of the LED then the battery should be replaced.
Combining the two buttons it results a lot of functions that will be explained in the followings.
5.5.1 Arming/disarming with confirmation by siren chirps and flashing lights
System arming/disarming
is simply made by
shortly pressing
(about 0,5s.) button 1.
The
system toggles to one state or another according to the current state.
The arming confirmation
is made
both optically and acoustically, by one signal
, and
the
disarming confirmation
will be made by
two optical-acoustical signals
(on flashing lights and
siren).
When arming:
1) If the system detects the hood, the trunk or a door opened, it warns by three optical-acoustical
signals and bypasses the respective inputs during arming. If afterwards the respective inputs are
restored (closing the hood, trunk or doors) they become active.
After sensors stabilization delay (20s. after arming), by opening again any door, the hood or the
trunk the alarm will be triggered.
2) If the system detects the position lights turned on, it will warn by a signal similar to the proximity
approach warning, according to the value of parameter 10.
When disarming
, if the alarm has been triggered while armed, four optical-acoustical signals will
be emitted.
Note:
1)
After arming the first 5s. are reserved for supplemental commands such as:
2)
manual sensors bypass by remote control (the proximity sensor, the shock sensor and the
ultrasonic sensor);
3)
silent alarm enabling (the siren is disabled);
4)
System disarming can only be made after the 5s after arming command;
5)
If the parameter 11 - Door contacts delay when arming is enabled, then the doors pin-
switches are tested only after delay duration estabilished by parameter 12. If, the delay duration is
over and the system detects at least one opened door, it will warn by three optical-acoustical
signals and it will bypass the respective input during arming.
6)
If afterwards all the doors are closed, the respective input becomes active again, after
sensors stabilization delay (20s after arming).
5.5.2 Arming/disarming silent
When no acoustical confirmation is needed, press the button 1 for about 2s instead of the short
press described before (0.5s). All the signals will become silent, meaning that the optical confirma-
tion only will remain active for respective arming/disarming period (warning for reverse car moving,
for door open, for arming with position lights turned ON, for silent siren, for sensors bypassing by
remote control, for doors, hood and trunck bypassing, for faulted sensors disabling when arming).
5.5.3 Remote controlled bypassing the sensors
Remote controlled bypassing the sensors
can only be made during the first 5s after the
arming command.
The bypass order is: proximity sensor -> shock sensor -> ultrasonic
sensor.
If the button 1 of the remote control is pressed, the system bypasses respective sensor, confirms
