27
Options
1) USB I/O set MX00
Optional input/output kit to connect the mixing panel with a computer. The USB connector
contains 1 stereo input signal and 1 stereo record output signal. With this option music can be
played from a computer via USB. Simultaneous the mixed music can be recorded via the
computer. The option must be built in as follows: First pull off the fader knobs (9, 14, 15 & 19) at
the frontpanel. Then unscrew the aluminum fader cover plate (4 screws). Take of this aluminum
plate. Then unscrew the bottombox, 2 screws at the frontpanel, one screw at each side and 2
screws at the bottom.
Screw of the hole cover plate (at the backpanel) which covers the desired hole for the USB
option set. Place the USB option so that the 6 pole angled connector on the USB PCB fits in
the 6 pole angled connector on the input PCB. Screw the screw in the hole in the backpanel to
mount the USB option kit. Close the mixing panel again by replacing the bottombox (6 screws),
the aluminum fader cover plate (4 screws) and the fader knobs (6 pieces).
Connect the USB I/O set to a computer via a USB-cable. The computer will recognize the USB
I/O set. Select the USB I/O set as playback- and recording device in the sound and audio
configuration menu of the computer or audio-software.
The USB I/O set MX00 can be ordered at every authorized RODEC-dealer.
Order code: 94 001 0070
2) Digital optical input channel fader MX00 set
Users can upgrade their mixing panel with digital faders on the music input channels. The
digital faders replace the standard analogue faders. The option must be built in as follows: First
pull off the fader knobs (9, 14, 15 & 19) at the frontpanel. Then unscrew the aluminum fader
cover plate (4 screws). Take of this aluminum plate. Unscrew the channel fader, which you like
to replace (2 screws). Pull off the 4 pole flat cable at the input PCB. Place the 10 pole flatcable
(delivered together with the digital optical input channel fader set) on the 10 pole connector
(right below the PFL switch) on the input channel PCB. Connect the other side of the flatcable
to the digital optical input channel fader. Screw the fader to the frontpanel (2 screws), attention,
the 10 pole connector on the fader PCB must be placed at the side of the crossfader (14).
Replace the aluminum fader cover plate and fader knobs. The digital optical input channel fader
is ready to use.
The digital optical input channel fader MX00 set can be ordered at every authorized RODEC-
dealer.
Order code: 94 001 0072
3) Digital optical crossfader MX00 set
The standard analogue crossfader can be upgraded by a digital optical crossfader. The option
must be built in as follows: First pull off the fader knobs (9, 14, 15 & 19) at the frontpanel. Then
unscrew the aluminum fader cover plate (4 screws). Take of this aluminum plate. Then unscrew
the bottombox, 2 screws at the frontpanel, one screw at each side and 2 screws at the bottom.
Unscrew the crossfader (2 screws). Pull off the 4-pole flatcable of the crossfader on the output
PCB. Place the 10 pole flatcable (delivered together with the digital optical crossfader set on
the 10 pole connector on the output PCB. Connect the other side of the flatcable to the digital
optical crossfader. Screw the digital optical crossfader to the frontpanel (2 screws), attention,
the 10 pole connector on the fader PCB must be placed at the opposite side of the output PCB.
Replace the bottombox (6 screws), the aluminum fader cover plate (4 screws) and fader knobs.
The digital optical cross fader is ready to use.
The digital optical cross fader MX00 set can be ordered at every authorized RODEC-dealer.
Order code: 94 001 0073