9
CordleSS drill/driver
eNG
1 - 4 for driving small screws
5 - 9 for driving screws into soft material
10 - 15 for driving screws into soft and hard material
16-18 for driving screws into hard wood
for heavy drilling
6. SiGhT liGhT
The Sight Light allows you to keep a clear view under
less illuminated circumstances. To turn on the light
simply press the On/Off Switch. When you release the
On/Off Switch, the light will be off.
7. drilliNG
When drilling into a hard smooth surface, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off center as the hole
is started. Hold the tool firmly and place the tip of the
bit at the point to be drilled. Depress the Switch trigger
to start the tool. Move the drill bit into the workpiece,
applying only enough pressure to keep the bit cutting.
Do not force or apply side pressure to elongate a hole.
Tungsten carbide drill bits should always
be used for concrete and masonry. when
drilling in metal, only use hSS drill bits in good
condition. Always use a magnetic bit holder (not
included) when using short screwdriver bits.
when screw-driving, apply a small quantity of
liquid soap or similar to the screw threads to
ease insertion.
8. diSPoSAl oF AN eXhAuSTed bATTery PACK
To preserve natural resources, please recycle or
dispose of the Battery Pack properly. This
Battery Pack contains Lithium batteries. Consult
your local waste authority for information regarding
available recycling and/or disposal options. Discharge
your Battery Pack by operating your drill, then remove
the Battery Pack from the drill housing and cover the
Battery Pack connections with heavy-duty adhesive
tape to prevent short circuit and energy discharge. Do
not attempt to open or remove any of the components.
9. overloAd ProTeCTioN
When overloaded, the motor comes to a stop. Release
the on/off button, and the machine will restart
immediately.
10. TemPerATure dePeNdeNT overloAd
ProTeCTioN
To perform as intended the power tool cannot be subject
to overload. When the load is too high or the allowable
battery temperature of 158°F (70°C) is exceeded, the
electronic control switches off the power tool until the
temperature is in the optimum temperature range again.
11. ProTeCTioN AGAiNST deeP diSChArGiNG
The Li-Ion battery is protected against deep discharging
by the “Discharging Protection System”. When the
battery is empty, the machine is switched off by means
of a protective circuit: In a warm environment or after
heavy use, the battery pack may become too hot to
permit charging. Allow time for the battery to cool down
before recharging. When the battery is charged for the
first time and after prolonged storage, the battery will
only accept approximately 60% charge. However, after
several charge and discharge cycles the battery will
accept a 100% charge.
TroubleShooTiNG
1. why doeS The drill NoT TurN oN wheN you
PreSS The SwiTCh?
The Forward/Reverse Rotation Control, which is on top
of the trigger, is positioned in the lock function. Unlock
the Forward/Reverse Rotation Control by putting it into
the required rotation position. Push the trigger and the
drill will start to rotate.
2. The drill SToPS beFore The SCrew iS
ComPleTely TiGhTeNed. why?
Verify the torque position of the Torque Adjusting
Ring. You can find the Torque-Adjusting Ring between
the Chuck and the drill body. Position 1 is the lowest
torque (screw driving force) and position 18 is the
highest torque (screw driving force). Position is for
drill operation. Regulate the Torque Adjusting Ring to a
higher position to reach the best result.
3. i CANNoT FiT The bATTery iNTo The bATTery
ChArGer. why?
The battery can be inserted into the charger only in
one direction. Turn the battery around until it can be
inserted into the slot.
4. reASoNS For diFFereNT bATTery PACK
worKiNG TimeS
Charging time problems, as above, and having not used
