Rockwell RK2856, Инструкции по безопасности и эксплуатации для пользователя

Страница: 9 / 52

20V LI DRILL DRIVER ENG
9
TECHNICAL DATA
Charger voltage 120 V~60 Hz
Rated voltage 20 V Max*
Nominal voltage 18 V
No load speed 0-350/0-1300/min
Number of clutch positions 15+1
Max torque 265 in-lbs
Chuck capacity 3/8˝
Max. drilling capacity Steel 3/8˝
Wood 1˝
Machine weight 2.8 lbs
*Voltage measured without workload. Initial battery
voltage reaches maximum of 20 volts. Nominal voltage
is 18 volts.
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
WARNING:
Use clamps or another practical way
to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
1. TO REMOVE OR INSTALL BATTERY PACK
(See Fig. A1, A2)
Depress the Battery Pack Release Button (7) to release
and slide the Battery Pack (8) out from your tool. After
recharge, slide it back into your tool. A simple push and
slight pressure will be sufficient.
2. HOW TO USE THE HOOK (See Fig. B1, B2)
Screw the HOOK on the tool with the screw provided in
the plastic bag. The HOOK (6) can be hooked on your belt
or pocket, etc.
3. ON/OFF SWITCH (See Fig. C)
Depress the On/Off switch (9) to start and release it to
stop your drill. The On/Off Switch is fitted with a brake
function which stops your Chuck immediately when you
quickly release the switch.
It is also a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed
is controlled by the amount of switch trigger depression.
WARNING: Do not operate for long periods
at low speed because excess heat will be
produced internally.
4. SWITCH LOCK
The On/off Switch (9) can be locked in the OFF position.
This helps to reduce the possibility of accidental starting
when not in use. To lock the On/off Switch, place the
Rotation Control in the center position.
5. REVERSIBLE (See Fig. D1, D2)
For drilling and screw driving use forward rotation
marked “
” (lever is moved to the left). Only use
reverse rotation marked “ ” (lever is moved to the
right) to remove screws or release a jammed drill bit.
WARNING: Never change the direction of
rotation when the Chuck is rotating, wait
until it has stopped!
6. TWO-SPEED GEAR CONTROL (See Fig. E)
The drill has a Two-Speed Gear Control (3) designed
for drilling or driving at LO (mark is 1) or HI (mark is 2)
speeds. A slide switch is located on top of the drill to
select either LO or HI speed. When using the drill in the
LO speed range, the speed will decrease and the drill will
have greater power and torque. When using the drill in
the HI speed range, the speed will increase and the drill
will have less power and torque.
Gear I
Low speed range: for screwdriving or working with large
drilling diameter
Gear II
High speed range: for working with small drilling
diameter
WARNING: To prevent gear damage, always
allow the chuck to come to a complete stop
before changing the direction of rotation.
7. CHUCK ADJUSTMENT (See Fig. F)
With the chuck facing you, rotate the chuck
counterclockwise to open the jaws. Insert the drill bit
between the chuck jaws. Rotate the chuck clockwise to
tighten the jaws. Insure that the drill bit is seated in the
center of the jaws.
8. TORQUE ADJUSTMENT (See Fig. G)
(Screw driving force of your drill driver)
The torque is adjusted by rotating the Torque Adjustment
Ring (2). The torque is greater when the Torque
Adjustment Ring is set on a higher setting. The torque is
less when the Torque Adjustment Ring is set on a lower
setting.
Make the setting as follows: