Rockwell Automation Samsung NX-CPU700p Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 122

Rockwell Automation Samsung NX-CPU700p Скачать руководство пользователя страница 9

9

I/O Backplanes and I/O Points

•

Flexible system configuration: 5 types of backplane (3-, 5-, 8-, 10-
and 12-slot)

The NX-CPU700p PLC has 5 types of backplane (3-, 5-, 8-, 10 and
12-slot type), providing you with very flexible I/O configuration.

All backplanes, I/O modules, power supply, and specialty
modules are available to other NX700 series PLC systems, for
example, NX-CPU700 or NX-CPU750A system.

•

Maximum 1600 I/O points

With a 12-slot base backplane and a 12-slot expansion
backplane, you can use up to 1600 I/O points by configuring
all I/Os with 64-point digital I/O modules.

3-Slot Type

5-Slot Type

8-Slot Type

10-Slot Type

12-Slot Type

NX-BASE03
48 Points: 16-point I/O
192 Points: 32-point I/O

NX-BASE0)
80 Points: 16-point I/O
320 Points: 64-point I/O

NX-BASE08
128 Points: 16-point I/O
512 Points: 64-point I/O

NX-BASE10
160 Points: 16-point I/O
640 Points: 64-point I/O

NX-BASE12
192 Points: 16-point I/O
768 Points: 64-point I/O

«
...
7
8
9
10
11
...
»

Содержание Samsung NX-CPU700p



























































































































Отзывы:

Нет отзывов