manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex SCR, Руководство пользователя

Поделиться
Скачать
Rockwell Automation Allen-Bradley PowerFlex SCR Скачать руководство пользователя страница 17

Installation/Wiring

1-3

PowerFlex SCR Bus Supply User Manual

Publication 20S-UM001G-EN-P

 

 

 

Minimum Mounting 

Clearances

The cabinet air inlet and outlet areas for each SCR Bus Supply must be a 
minimum of 200 cm

2

 (31 in.

2

). The length-to-width ratio must not exceed 

4:1.

Figure 1.2 Mounting Clearances  

Ambient Operating Temperatures

The PowerFlex SCR Bus Supply is designed to operate at 0…40 °C 
(32…104 °F) ambient without derating. For operation in ambients above 
40 °C up to 50 °C (104 °F up to 122 °F), the PowerFlex SCR Bus Supply 
output Amps must be derated by 1.2% per 1 °C for 400A unit, and by 1.0% 
per 1 °C for 600A and 1000A units.

Ensure that proper cooling is provided to the SCR Bus Supply to maintain 
the 40 °C rated specification. If the ambient temperature is exceeded, apply 
the proper derate factors. Add exhaust fans to the front or top of the 
enclosure bay and provide a filtered opening at the bottom of the cabinet 
bay.

The SCR Bus Supply watt losses (from specification section) are 1200W at 
400A, 1600W at 600A, 2700W at 480V 1000A, and 2800W at 690V 
1000A. The three-phase AC line reactor watt losses are listed in the 1321 
Power Conditioning Products Technical Data (publication 1321-TD001).

Because of the internal design of the SCR Bus Supply, it is NOT 
recommended to rely on an air dam surrounding the SCR Bus Supply.

It is recommended that the system integrator completes a thermal evaluation 
to ensure adequate cooling to maintain proper operating conditions for each 
cabinet or bay. A minimum air exchange of 725 CFM per SCR Bus Supply 
is recommended.

120 mm

(4.7 in.)

120 mm

(4.7 in.)

150 mm

(6 in.)

300 mm

(12 in.)

Air Flow

Air Flow

Air Flow

Air Outlet

PowerFlex

SCR

Bus Supply

PowerFlex

SCR

Bus Supply

Air Outlet

Air Inlet

Air Inlet

Refer to 

Appendix A

 for detailed dimension information.

below fan

Содержание Allen-Bradley PowerFlex SCR





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды