Rockwell Automation Allen-Bradley PowerFlex 755T Series Скачать руководство пользователя страница 108

Страница: 108 / 130

108

Rockwell Automation Publication 750-PM101B-EN-P - April 2022

Chapter 4 Troubleshooting

193 IdCompMtrnIq

This signal displays the corresponding Iq Ref values

for IdComp during motoring operation.

REAL

194 IdCompMtrnPu

This signal displays the required IdComp values

during motoring.

REAL

195 IdCompRegnIq

This signal displays the corresponding Iq Ref values

for IdComp during regen operation.

REAL

196 IdCompRegnPu

This signal displays the required IdComp values

during regen operation.

REAL

197 FlxIdSyncRef

This signal is the d-axis current reference, which is

the output of the flux regulator.

REAL

PkA

198 NegIdsLim

If this signal is non-zero, then the flux regulator is at

negative Id current limit.

DINT

t/f

199 PosIdsLim

If this signal is non-zero, then the flux regulator is at

positive Id current limit.

DINT

t/f

200 VqsFdbkFltrd

This signal is the filtered q-axis voltage feedback.

REAL

PkV

210 FLARPM

This signal is the Slip RPM at full load amps, which is

calculated based on the filtered slip gain.

REAL

RPM

211 OmegSlipFilt

This signal is the filtered slip in rad/sec.

REAL

R/S

212 RsGain

This signal is the Rs gain, which is calculated based

on the filtered slip gain.

REAL

213 SlipGnFltrd

This signal is the filtered slip gain.

REAL

R/S/A

214 SlipGnLatchd

This signal is the latched slip gain in the slip

regulator.

REAL

R/S/A

215 SlipGnLmtd

This signal is the limited slip gain, which is the slip

regulator output.

REAL

R/S/A

216 SlipLoTrqLim

If this signal is non-zero, then the slip regulator is

not active because the q-axis current reference is

below the set value.

DINT

t/f

217 SlipGnMaxLim

If this signal is non-zero, then the slip regulator is at

maximum slip gain limit.

DINT

t/f

218 SlipGnMinLim

If this signal is non-zero, then the slip regulator is at

minimum slip gain limit.

DINT

t/f

219 SlipIntegOut

This signal is the integration term of the slip

regulator output.

REAL

R/S/A

220 SlipPropOut

This signal is the proportional term of the slip

regulator output.

REAL

R/S/A

221 VdsFdbkFltrd

This signal is the filtered d-axis voltage feedback.

REAL

PkV

230 IdSyncRef

Flux current command.

REAL

PkA

231 IqSyncRef

Torque command.

REAL

PkA

232 VdSyncFF_Ref

This signal is the feed forward d-axis voltage

reference.

REAL

PkV

233 VqSyncFF_Ref

This signal is the feed forward q-axis voltage

reference.

REAL

PkV

240 LambdaDsSync

This signal is the d-axis stator flux.

REAL

VSec

241 LambdaDsFilt

This signal is the filtered d-axis stator flux.

REAL

VSec

242 LambdaQsSync

This signal is the q-axis stator flux.

REAL

VSec

243 LambdaQsFilt

This signal is the filtered q-axis stator flux.

REAL

VSec

250 TrqEst

This signal is the estimated torque in N•m.

REAL

251 TrqEstFltrd

This signal is the filtered estimated torque in N•m.

REAL

255 ActvCurLim

This is the active current limit value.

REAL

PkA

260 FluxCurMax

This is the maximum flux current value.

REAL

PkA

261 FluxCurMin

This is the minimum flux current value.

REAL

PkA

262 LambdaDsRtd

This signal is the rated d-axis stator flux.

REAL

VSec

263 MtrRtdTrq

This is the motor rated torque value in N•m that is

calculated from motor name plate data.

REAL

264 SlipGnRtd

This is the rated slip gain value.

REAL

R/S/A

Port 10 Testpoint Codes (Continued)

No. Name

Description

Data Type

Units

Содержание Allen-Bradley PowerFlex 755T Series



































































































































Результаты поиска

Содержание Allen-Bradley PowerFlex 755T Series

Отзывы:

Rockwell Automation Allen-Bradley PowerFlex 755T Series, Руководство по программированию, Страница: 108 / 130

Результаты поиска

Содержание Allen-Bradley PowerFlex 755T Series

Отзывы: