Rockwell Automation Allen-Bradley PowerFlex 755T Series Скачать руководство пользователя страница 107

Страница: 107 / 130

Rockwell Automation Publication 750-PM101B-EN-P - April 2022

107

Chapter 4 Troubleshooting

116 IbFbk

B-phase simultaneously sampled current feedback

scaled to units of the system.

REAL

PkA

117 IcFbk

C-phase simultaneously sampled current feedback

scaled to units of the system.

REAL

PkA

120 FreqSync Enhanced

Delay

This signal indicates the status of the delay when

Flying Start function is activated. This is for the

CEMF mode of the Flying Start function.

DINT

t/f

121 FreqSync Enhanced

State

This signal indicates the status of flying start

operating state. This is for the CEMF mode of the

Flying Start function.

DINT

t/f

122 FreqSync Sweep State

This signal indicates the status of flying start

operating state. This is for the Sweep mode of the

Flying Start function.

DINT

t/f

125 PrchrgState

State of the Precharge state machine.

DINT

t/f

130 LineLoss Act

If this signal is non-zero, then a Line Loss condition

is active. If this signal is zero, then a Line Loss

condition is not active.

DINT

t/f

135 Power State Handler

The present state being executed by the power state

handler.

DINT

t/f

136 PwrStateCmd

Commanded state from the PowerStateMach to the

PowerStateHandler.

DINT

t/f

140 Current Limit Stop

Active

If this signal is non-zero, then a Current Limit

Stopping Sequence is active. If this signal is zero,

then a Current Limit Stopping Sequence is not

active.

DINT

t/f

141 Sequencer State

The present state of the Sequencer.

DINT

t/f

145 ActvPwmFreq

Active PWM frequency

REAL

146 MaxJuncTemp

Active max junction temperature used in thermal

manager.

REAL

°C

150 TrqRefAtZero

If this signal is non-zero, then the

10:2150 [Trq Ref Filt In] will be forced to a value of

zero. If this signal is zero, then the Torque

Reference is supplied by 10:2076 [Trq Ref Selected]

after offset by the Friction Compensation and

Torque Step signals. This signal could become non-

zero as part of a stop sequence or during Autotune.

DINT

t/f

155 RideThruRcvrLvl

This is the level of DC Bus voltage where the PWM

can become active again when power loss has

occurred and power is recovered.

REAL

VDC

156 RideThruStrtLvl

This is the level of bus voltage where the PwrLoss

mode is triggered.

REAL

VDC

157 VbusUnderVltgLvl

This is the level set to trigger a bus under voltage

event.

REAL

VDC

160 Theta_e

This signal is the Theta_e, the electrical stator angle,

in radians.

REAL

Rad

161 Theta_r

This signal is the Theta_r, the electrical rotor angle,

in radians.

REAL

Rad

170 IdSyncFdbk

Flux current feedback.

REAL

PkA

171 IqSyncFdbk

Torque current feedback.

REAL

PkA

172 VdSyncFdbk

This signal is the d-axis voltage feedback.

REAL

PkV

173 VqSyncFdbk

This signal is the q-axis voltage feedback.

REAL

PkV

180 VdsCmd

D-axis voltage command in synchronous reference

frame.

REAL

PkV

181 VqsCmd

Q-axis voltage command in synchronous reference

frame.

REAL

PkV

190 FieldWeakSts

If this signal is non-zero, then the field weakening

control is active.

DINT

t/f

191 FluxRegFdFwd

This signal is the flux regulator output feed forward

term.

REAL

PkA

192 FlxRegOmgLim

If this signal is non-zero, then the flux regulator is

not active. If this signal is zero, then the flux

regulator is active.

DINT

t/f

Port 10 Testpoint Codes (Continued)

No. Name

Description

Data Type

Units

Содержание Allen-Bradley PowerFlex 755T Series



































































































































Результаты поиска

Содержание Allen-Bradley PowerFlex 755T Series

Отзывы:

Rockwell Automation Allen-Bradley PowerFlex 755T Series, Руководство по программированию, Страница: 107 / 130

Результаты поиска

Содержание Allen-Bradley PowerFlex 755T Series

Отзывы: