Rockwell Automation Allen-Bradley AADvance T9110 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 165

background image

48

Rockwell Automation Publication ICSTT-RM447M-EN-P - July 2019

Chapter 2

The AADvance Safety Controller

Processor Firmware Upgrades

You can check the firmware revision of you processor modules without
removing them to read the label and you can upgrade the firmware revision of
the processor modules. Upgrading the firmware in the 9110 processor module
is done in the Recovery Mode and is a two-stage process:

• Stage 1: Run the latest version of 350720_xxx_ControlFLASH.msi

program to install the ControlFLASH™ firmware upgrade kit for the
Recovery Mode on your PC. Then run the ControlFLASH utility to
upgrade your processor module and install the Recovery Mode. If your
module is delivered with the Recovery Mode installed then this stage is
not necessary.

Stage 1 must be performed individually on each processor; it does not
matter if you download the Recovery Mode one at a time in a specific
slot or in their own slots.

• Stage 2: Reboot the processor and press and hold the Fault Reset button

to enter the Recovery Mode. Then run the latest version of
354400_xxxx_ControlFLASH.msi program to install the
ControlFLASH to upgrade your processor's OS, FPGA, LSP and
BUSP.

When stage 1 is completed ControlFLASH can be used to upgrade
three processor modules in the same processor base unit all at the same
time.

Tools and Resources

You will need the ControlFLASH firmware upgrade kit.

• Quick Start and RSLinx Classic Lite software or better.
• ControlFLASH programming tool, along with its required support

drivers and on line HELP.

• Firmware for the processor modules being upgraded.

Ethernet Communication Protocols

AADvance Ethernet ports are used to support several transport layer services;
these services are listed in the following table:

NOTE

Detailed information and procedures on firmware revision are given in the
AADvance Configuration Guide Doc No: ICSTT-RM405 and AADvance
Configuration Guide Doc No: ICSTT-RM458 for Workbench 2.0.

Protocol

Port Number

Purpose

TCP

502

MODBUS Slave

TCP

1132

ISaGRAF, application downloads, debug, SoE

TCP

10001-10006

Transparent Communication Interface (Serial Tunnelling)

«
...
46
47
48
49
50
...
»

Содержание Allen-Bradley AADvance T9110






































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Allen-Bradley AADvance T9110

Бренд: OmarLift Страницы: 14

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

Бренд: Harsco Industrial Страницы: 57

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 11

Бренд: Nauticam Страницы: 2

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 20

GEMINI C Series

Бренд: NAPCO Страницы: 24

Бренд: Watts Страницы: 24

Бренд: Patron Страницы: 36

Бренд: YASKAWA Страницы: 42

Бренд: YASKAWA Страницы: 351

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды