Rockwell Automation Allen-Bradley 1790D-N0C2 Скачать руководство пользователя страница 50

Страница: 50 / 64

Rockwell Automation Publication 1790-UM001B-EN-P - April 2021

Appendix A Install, Wire, and Configure PROFIBUS Modules

You can mount your blocks on a panel or DIN rail as described in the previous
section.

Connect the PROFIBUS DP Terminal Connector

Follow these procedures when connecting the PROFIBUS DP terminal
connector to the base block.

The required PROFIBUS female 9-pin D-sub connector is not supplied with the
base block; you must purchase it separately. Before you connect the female 9-
pin D-sub connector to the base block, make sure it is wired correctly, as
shown in

Table 40

Once you have properly wired the connector, attach it to the base block as
shown in

Figure 22

. Use the locking screws on the connector to fasten it to the

base block.

Horizontal mounting

Vertical mounting

The longer expansion cable
(1790-15CMCBL) allows up to 7 cm
(2.75 in.) of space between blocks.

WARNING:

If you connect or disconnect the PROFIBUS cable with power

applied to this module or any device on the network, an electrical arc

can occur. This could cause an explosion in hazardous location

installations. Be sure that power is removed or the area is nonhazardous

before proceeding.

Table 40 - Wiring Connections

Pin Number

Name

Description

Shield

Shield, protective ground

M24V

Minus 24V output voltage

RxD/TxD-P

Receive/transmit-data-P

CNTR-P

Control-p

DGND

Data ground

Voltage-plus

P24V

Plus 24V output voltage

RxD/TxD-N

Receive/transmit-data-N

CNTR-N

Control-N

Содержание Allen-Bradley 1790D-N0C2

































































Результаты поиска

Содержание Allen-Bradley 1790D-N0C2

Отзывы:

Похожие инструкции для Allen-Bradley 1790D-N0C2

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley 1790D-N0C2, Руководство пользователя

Результаты поиска

Содержание Allen-Bradley 1790D-N0C2

Отзывы:

Похожие инструкции для Allen-Bradley 1790D-N0C2

Бренды по названию

Популярные бренды