Rockwell Automation Allen-Bradley 1790D-N0C2 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 64

background image

48

Rockwell Automation Publication 1790-UM001B-EN-P - April 2021

Appendix A Install, Wire, and Configure PROFIBUS Modules

Group your modules in the enclosure to minimize adverse effects from
radiated electrical noise and heat. Consider the following conditions when
selecting a location for the analog module. Position the module:

•

away from sources of electrical noise such as hard-contact switches,
relays, and AC motor drives

•

away from modules that generate significant radiated heat.

In addition, route shielded, twisted-pair analog input and output wiring away
from any high-voltage I/O wiring.

Protect the Circuit Board from Contamination

The printed circuit boards of the analog modules must be protected from dirt,
oil, moisture, and other airborne contaminants. To protect these boards, the
system must be installed in an enclosure suitable for the environment. The
interior of the enclosure should be kept clean and the enclosure door should be
kept closed whenever possible.

Install the CompactBlock LDX

I/O Block

Follow these steps to install the block:

1.

Set the Station Address on the Base Block

2.

Mount the Base Block

3.

Connect the PROFIBUS DP Terminal Connector

4.

Connect Power to the Block

Set the Station Address on the Base Block

To set the station address, adjust the switches on the front of the base block.
The two switches are most significant digit (MSD) and least significant digit
(LSD). The switches can be set from 00 to 99 and are read at base block power-
up only.

shows an example base block set for station address 11.

Figure 21 - Node Address Settings

Mount the Base Block

You can mount the base block to a panel or DIN rail. We recommend that you
ground the panel or DIN rail before mounting the block.

IMPORTANT

The analog base module can accommodate a

maximum

of two

discrete expansion modules.

NODE ADDRESS

MOD

NET

STATUS

LSD

MSD

Node Address is set to 11

«
...
46
47
48
49
50
...
»

Содержание Allen-Bradley 1790D-N0C2

































































Отзывы:

Нет отзывов

Похожие инструкции для Allen-Bradley 1790D-N0C2

Бренд: Valcom Страницы: 8

CPX-AP-I-8DI-M8-3P

Бренд: Festo Страницы: 18

Бренд: Sandstrom Страницы: 32

Бренд: Niko Страницы: 104

Бренд: D-Box Страницы: 12

Бренд: Nußbaum Hebetechnik Страницы: 32

Бренд: DOLD Страницы: 20

Institutional Series I-35

Бренд: Hunter Страницы: 2

Бренд: Fancom Страницы: 51

Бренд: LIFTINGITALIA Страницы: 24

Бренд: American Panel Страницы: 18

Aureon 7.1 FireWire

Бренд: TerraTec Страницы: 2

Бренд: GST Страницы: 3

Бренд: Farfisa Страницы: 48

Бренд: M-system Страницы: 10

SwitchPoint Infinity 3

Бренд: Stryker Страницы: 124

Бренд: Sorex wireless Страницы: 35

Бренд: human care Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды