background image

10

40752-195 (1)

 

Effective 

2

/201

1

4-15 . The Remote Maintenance Mode is enabled by apply-

ing 24VDC to the two wire cable that exists the left side of the 

breaker.  The wires are color coded as follows:  24V 

and Black=common ground.  A blue colored LED on the left side 

of the breaker is the Maintenance Mode section

of the trip unit

.

  The lighted blue LED indicates that the 

lowest setting of the Maintenance Mode is enabled.  This setting 

corresponds to 2.5x of In.  Turning the adjustable switch on the 

trip unit has no affect on either the Maintenance Mode or the

INST Mode settings while the blue LED is lit.  In addition to the

blue colored LED, a relay contact (C, NO) is available.  The wires

for this contact exit the left hand side of the breaker and are color

coded as follows:  Blue=C, and Red=NO. 

4-16 . The High Load Alarm Relay option will provide a SPST 

contact closure when the trip unit current equals or is greater than 

95% of In for a period of 38 seconds.  If the current drops below 

the 95% value, the contact will open.  The yellow and green wires 

that exit the right side of the breaker are the common (C) and nor

-

mally (NO) of this relay.  

4-17 . The Ground Fault Relay option will provide a SPST con-

tact closure immediately before the breaker will trip on a ground 

fault over current detect.  This closure is momentary (50ms) and 

the customer must provide the necessary external circuitry in or-

der to latch this signal.  The yellow and green wires that exit the 

right side of the breaker are the common (C) and normally (NO) 

of this relay.

NOTE:  Either the high Load Alarm Relay or the Ground Fault 

Alarm Relay option can be selected but not both.  The High 

Load Alarm Relay can only be selected with LS and LSI trip unit 

styles.  If the trip unit is a Ground Fault style, the Alarm A Relay, 

by default, will be selected.

NOTE:  The contact rating of the relay is:  

2A, 30

 

VDC

 

resistive load.

  The coil resistance is approximately 

1600 ohms. (Max switching voltage: 220 VDC, Max switching

current:  2A).

  The coil resistance is about 1600 ohms.

 

  

   

+

-

NO

NC

-

+

24 VOLT DC

LEFT SIDE OF BREAKER

YELLOW

BLACK

BLUE

RED

Содержание Allen-Bradley 140U

















Отзывы: