Rockwell Automation 440R-D22R2 страница 9 Скачать руководство пользователя | Manualshive

Страница: 9 / 90

background image

Rockwell Automation Publication 440R-UM013F-EN-P - July 2021

9

Chapter

1

Overview

The Guardmaster® safety relay (GSR) family is a group of advanced general-
purpose and special-purpose safety relays. This user manual addresses the CI,
DI, DIS, EM, EMD, and SI safety relays from this family of relays.

Hardware Features

Figure 1 - Safety Relays

Removable Terminal Blocks

Each relay module is only 22.5 mm (0.9 in.) wide with four removable terminal
blocks (two on top and two on bottom). The terminal blocks are keyed to
confirm that they are installed in their proper slots. See

Removal and Replacement on page 75

.

Status Indicators

Multiple status indicators provide status and diagnostics. Under fault
conditions, the PWR/Fault status indicator blinks in specific patterns to help
diagnose the fault. See

Status Indicators on page 35

and

View the PWR/Fault

Status Indicator (Step 1) on page 54

for more information.

Multi-position Switches

Most safety relays are configured by adjusting multi-position switches to set
their functionality.

(a)

The switches are on the front face of the relay so you can

see the set position during, and after, configuration. During the configuration
process, status indicators on the front face of the relay confirm the switch
settings. See

Switch Adjustment on page 31

for more information.

(a) The EM safety relay does not require configuration.

Removable Terminal Blocks

Status Indicators

Multi-position Switches

set functionality

Optical Communication Bus

«
...
7
8
9
10
11
...
»

Содержание 440R-D22R2



























































































Отзывы:

Нет отзывов

Похожие инструкции для 440R-D22R2

Бренд: GE Страницы: 33

Бренд: GE Страницы: 432

Бренд: GE Страницы: 46

Бренд: GE Страницы: 76

Бренд: F&F Страницы: 4

efector100 G1503S

Бренд: IFM Страницы: 47

Бренд: IFM Страницы: 29

Бренд: DEEsys Страницы: 6

Luxomat ViSTATION-KNX REG

Бренд: B.E.G. Страницы: 4

Relion 615 series

Бренд: ABB Страницы: 156

Бренд: GE Страницы: 175

Multilin TOV40 Series

Бренд: GE Страницы: 27

Бренд: Omron Страницы: 4

Бренд: Omron Страницы: 4

Бренд: Omron Страницы: 16

Бренд: Omron Страницы: 9

Бренд: Omron Страницы: 8

K8AK-AS1 24VAC/DC

Бренд: Omron Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды