RockShox 35 2020 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 47

RockShox 35 2020 Скачать руководство пользователя страница 28

28

Air Spring Installation

Retaining rings have a sharper edged side and a rounder edged side.
Installing retaining rings with the sharper edged side facing the tool
will allow for easier installation and removal.

Guide the retaining ring with your finger to prevent scratching the air
shaft.
Place the tips of the retaining ring pliers into the eyelets of the retaining
ring, then use the pliers to push the seal head into the upper tube while
installing the retaining ring into the groove.

Confirm the retaining ring is properly seated in the retaining ring

groove by using the retaining ring pliers to rotate the retaining ring

and seal head back and forth a few times.

NOTICE

Do not scratch the air spring shaft. Scratches on the air shaft will allow
air to bypass the seal head into the lower leg, resulting in reduced
spring performance.

Thread the bottom bolt into the air shaft and pull the air shaft until it
stops.

Inject or pour RockShox® suspension oil into the air spring upper tube.

8

Retaining ring pliers

9

10

5wt

RockShox Bleed Syringe

2 mL

«
...
26
27
28
29
30
...
»

Содержание 35 2020
















































Отзывы:

Нет отзывов