background image

3

PRODUCT SPECIFIC SAFETY WARNINGS

>  To avoid serious injury, keep hands and fingers away from the spinning router bit. 

  Maintain awareness of the bit at all times.

>  Turn off and unplug your router before installing or adjusting 

  the bit or adjusting the Router Table Fence.

>  BEFORE beginning any routing operation, ALWAYS make 

  sure that ALL knobs on the Router Table Fence have been 

  tightened and the fence will not shift during use.

>  Always feed the workpiece against the rotation of the bit. 

  A table-mounted router spins the bit counterclockwise, so 

  feed the workpiece from right to left as you face the table. 

  This provides better control because the rotation of the 

  bit is backward and toward the fence instead of forward 

  and away from it.

>  NEVER attempt to machine a workpiece at the router table 

  without using the Router Table Fence or a starter pin with 

  a bearing-guided bit. Failure to use these guides diminishes 

  your ability to control the workpiece and greatly increases 

  the chance of damage to the workpiece and/or serious 

  personal injury.

>  BEFORE plugging in and turning on the router, always 

  check to be sure that the MDF Adjustable Fence Faces (2) 

  are fully secured and that the bit can rotate freely without 

  touching the Fence Faces. An exception to this is if 

  you have set up the infeed Fence Face to provide 

  zero-clearance support for the workpiece, as described 

  in the “Adjusting the Fence Faces” section on Page 5.

>

  

Do NOT attempt to use the Bench Dog ProFence to joint 

board edges that are thicker than 1

1

4

". The maximum 

material thickness might be further limited by the cutting 

height of the router bit being used. For example, a bit with  

a 3/4" cutting height will be able to joint only boards that 

are 3/4" thick or less.

>   When working with narrow boards, use a push block  

or push stick to advance the workpiece to avoid fingers 

from contacting the bit and causing serious injury.

>   Use only 1/2" shank router bits for jointing. The thicker 

shank will provide less chatter and cleaner cuts. The  

bit’s cutting height must not exceed 1

1

2

".

>  Never use a router bit that is damaged or dull.

>   Never exceed the manufacturer’s recommended maximum 

operating speed for your router bit.

>  Set the Bit Safety Guard (3) directly over the router bit, 

  at least 1/2" above the top of the bit or the top of 

  the workpiece (whichever is highest) to make sure 

  that the bit doesn’t cut into the Bit Safety Guard (3).

>  When adjusting the position of the Router Table Fence, 

  make sure that no part of the Aluminum Fence (1) will 

  contact the router bit.

>   If using the Jointer Bars (12), always install them in pairs in 

matched slots in the Aluminum Fence (1) – either the first 

and the third slots from the top or the second and fourth. 

Failure to install both Jointer Bars in matched slots is likely 

to yield poor results.

>  NEVER FEED YOUR WORKPIECE BETWEEN THE 

  BIT AND THE FENCE. Because of the direction of the 

  bit’s rotation, the bit could “grab” the workpiece and 

  propel it away from the table at a high velocity, potentially 

  resulting in property damage and serious injury to 

  anyone in its path. 

>  Additionally, when the bit grabs the workpiece, 

  your hands could be drawn into the bit, resulting 

  in serious injury.

AVOID THIS SITUATION!

Fence

Workpiece

Bit Rotation

Feed 

Direction

Содержание ProFence 47905









Отзывы: