background image

 

Wait until the machine has reached its top

speed. You can then position the angle grinder
on the workpiece and machine it.

7.2 Changing the grinding wheels (Fig. 5)

Use the face spanner (5) supplied to change the
grinding wheels. 

Pull out the power plug.

n

Simple wheel change by spindle lock:

n

Press the spindle lock and allow the grinding
wheel to latch in place.

n

Open the flange nut with the face spanner. 

(Fig. 5)

n

Change the grinding or cutting wheel and tighten
the flange nut with the face spanner.

 

Important!

Only ever press the spindle lock when the motor
and grinding spindle are at a standstill!
You must keep the spindle lock pressed while
you change the wheel!

For grinding or cutting wheels up to approx. 3 mm
thick, screw on the flange nut with the flat side facing
the grinding or cutting wheel.

7.3 Flange arrangements when using grinding

wheels and cutting wheels (Fig. 6-9)

n

Flange arrangement when using a depressed-
centre or straight grinding wheel (Fig. 7)
a) Clamping flange
b) Flange nut

n

Flange arrangement when using a depressed-
centre cutting wheel (Fig. 8)
a) Clamping flange
b) Flange nut

n

Flange arrangement when using a straight
cutting wheel (Fig. 9)
a) Clamping flange
b) Flange nut

7.4 MOTOR

It is vital for the motor to be well ventilated during
operation. Be sure, therefore, to keep the ventilation
holes clean at all times.

7.5 GRINDING WHEELS

n

Never use a grinding or cutting wheel bigger than
the specified diameter.

n

Before using a grinding or cutting wheel, check
its rated speed. 

n

The wheel´s rated speed must be higher than the

idle speed of the right-angle grinder.

n

Use only grinding and cutting wheels that are
approved for a minimum speed of 11000 rpm
and a peripheral speed of 80 m/sec.

n

Check the direction of rotation when you use
diamond cutting wheels. The directional arrow on
the diamond cutting wheel must point in the
direction in which the tool rotates.

Take special care that the grinding/sanding wheels
are properly stored and transported. Ensure that the
grinding/sanding wheels are never exposed to shock,
jolts or sharp edges (for example during transport or
storage in a toolbox). This could cause damage (such
as cracks) to the grinding/sanding wheels and place
the user in serious danger.

7.6 OPERATING MODES

7.6.1 Rough grinding

 

Caution: Use the safety device for

sanding/grinding 

(included in items supplied)

.

For the best rough grinding results, hold the grinding
wheel at an angle of between 30° and 40° to the
workpiece surface and guide back and forth over the
workpiece in steady movements.

7.6.2 Cutting

 

Caution: Use the safety device for abrasive

cutting 

(available as accessory)

When you use the right-angle grinder for cutting
purposes, avoid tilting it in the cutting plane. The
cutting wheel must have a clean cutting edge.
A diamond cutting wheel is best used to cut hard
stone.

 

It is prohibited to use the machine on

asbestos materials!

Never use a cutting wheel for rough grinding.

8. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.

19

GB

Anleitung_RB_AG_850_SPK7__  07.11.13  07:32  Seite 19

Содержание 44.306.09

















































Отзывы: