ROBUA G Series Скачать руководство пользователя страница 26

Страница: 26 / 48

First start-up

Figure 4.4

Flame lockout lamp connection

Lockout lamp

X11

When the led comes on, in the manner described in Table

4.1

p. 26, it indicates the presence of a fault.

Table 4.1

Led status to signal faults

Fault

LED status

Flame lockout

Fixed

Limit thermostat trip or minimum flue gas temperature thermostat trip
(1)

Flashing (on = 4 seconds, off = 1 second) (2)

Other type of anomaly

Flashing (on = 1 second, off = 4 seconds) (2)

The flue gas temperature thermostat is present on the G series gas unit heaters.

After 72 hours of continuous flashing status, the led becomes fixed.

4.6

REMOTE THE ERROR RESET

Remote unlocking can also be performed. To do this, a

button must be connected to terminals X11 of the mo-

tor board (230V - 50Hz output, see diagram in Figure

4.5

p. 26).

Closing the contact causes the fault to be reset.

Figure 4.5

Flame lockout reset button connection

Reset button

X11

FIRST START-UP

First start-up entails checking/setting up the com-

bustion parameters and may exclusively be carried

out by a Robur TAC. NEITHER the user NOR the in-

stallation technician is authorised to perform such

operations, under penalty of voiding the warranty.

The installer is obliged to carry out preliminary

checks described in Paragraph 5.1

p. 26.

5.1

PRELIMINARY CHECKS

Paragraph dedicated to the installer.

5.1.1

Preliminary checks for first start-up

Upon completing installation, before contacting the TAC

the installer must check:

▶

Electrical and gas systems suitable for the required ca-

pacities and equipped with all safety and control de-

vices required by the regulations in force.

▶

Absence of leaks in the gas system.

▶

Type of gas for which the appliance is designed (natu-

ral gas, LPG or other gas).

▶

Supply gas pressure complying with the values of

Table 3.1

p. 17, with max tolerance ±15%.

▶

Correct operation of the flue exhaust duct.

▶

Combustion air feed and flue gas exhaust correctly

carried out according to the regulations in force.

▶

Power supply mains complying with the appliance's

rating plate data.

▶

Appliance correctly installed, according to the manu-

facturer's instructions.

▶

System installed in a workmanlike manner, according

to national and local regulations.

5.1.2

Abnormal or hazardous installation

situations

Should any abnormal or hazardous installation situations

be found, the TAC shall not perform first start-up and the

appliance shall not be commissioned.

These situations may be:

▶

Failed compliance with minimum clearances.

▶

Insufficient distance from combustible materials.

▶

Conditions that do not warrant access and mainte-

nance in safety.

▶

Appliance switched on/off with the main switch,

Содержание G Series

















































Результаты поиска

Содержание G Series

Отзывы:

Похожие инструкции для G Series

Бренды по названию

Популярные бренды

ROBUA G Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание G Series

Отзывы:

Похожие инструкции для G Series

Бренды по названию

Популярные бренды